Subject: Re: [PATCH] net: phy: marvell: initialise link partner state earlier

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

From: Russell King <[email-masked]>

Move the initialisation of the link partner state earlier, inside
marvell_read_status_page(), so we don't have the same initialisation
scattered amongst the other files.  This is in a similar place to
the genphy implementation, so would result in the same behaviour if
a PHY read error occurs.

This allows us to get rid of marvell_read_status_page_fixed(), which
became a pointless wrapper around genphy_read_status_fixed().

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/marvell.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
index 9a8badafea8a..81f2ceef70f7 100644
--- a/drivers/net/phy/marvell.c
+++ b/drivers/net/phy/marvell.c
@@ -1371,6 +1371,10 @@ static int marvell_read_status_page(struct phy_device *phydev, int page)
 	phydev->speed = SPEED_UNKNOWN;
 	phydev->duplex = DUPLEX_UNKNOWN;
 
+	linkmode_zero(phydev->lp_advertising);
+	phydev->pause = 0;
+	phydev->asym_pause = 0;
+
 	if (phydev->autoneg == AUTONEG_ENABLE)
 		err = marvell_read_status_page_an(phydev, fiber, status);
 	else

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

linkmode_test_bit() does not modify the address; test_bit() is also
declared const volatile for the same reason. There's no need for
linkmode_test_bit() to be any different, and allows implementation of
helpers that take a const linkmode pointer.

Signed-off-by: Russell King <[email-masked]>
---
 include/linux/linkmode.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/include/linux/linkmode.h b/include/linux/linkmode.h
index fe740031339d..8e5b352e44f2 100644
--- a/include/linux/linkmode.h
+++ b/include/linux/linkmode.h
@@ -71,7 +71,7 @@ static inline void linkmode_change_bit(int nr, volatile unsigned long *addr)
 	__change_bit(nr, addr);
 }
 
-static inline int linkmode_test_bit(int nr, volatile unsigned long *addr)
+static inline int linkmode_test_bit(int nr, const volatile unsigned long *addr)
 {
 	return test_bit(nr, addr);
 }

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

Add a couple of helpers to resolve negotiated flow control. Two helpers
are provided:

- linkmode_resolve_pause() which takes the link partner and local
  advertisements, and decodes whether we should enable TX or RX pause
  at the MAC. This is useful outside of phylib, e.g. in phylink.
- phy_get_pause(), which returns the TX/RX enablement status for the
  current negotiation results of the PHY.

This allows us to centralise the flow control resolution, rather than
spreading it around.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/Makefile     |  3 ++-
 drivers/net/phy/linkmode.c   | 44 ++++++++++++++++++++++++++++++++++++++++++++
 drivers/net/phy/phy_device.c | 26 ++++++++++++++++++++++++++
 include/linux/linkmode.h     |  4 ++++
 include/linux/phy.h          |  3 +++
 5 files changed, 79 insertions(+), 1 deletion(-)
 create mode 100644 drivers/net/phy/linkmode.c

diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index fe5badf13b65..d523fd5670e4 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -1,7 +1,8 @@
 # SPDX-License-Identifier: GPL-2.0
 # Makefile for Linux PHY drivers and MDIO bus drivers
 
-libphy-y			:= phy.o phy-c45.o phy-core.o phy_device.o
+libphy-y			:= phy.o phy-c45.o phy-core.o phy_device.o \
+				   linkmode.o
 mdio-bus-y			+= mdio_bus.o mdio_device.o
 
 ifdef CONFIG_MDIO_DEVICE
diff --git a/drivers/net/phy/linkmode.c b/drivers/net/phy/linkmode.c
new file mode 100644
index 000000000000..969918795228
--- /dev/null
+++ b/drivers/net/phy/linkmode.c
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: GPL-2.0+
+#include <linux/linkmode.h>
+
+/**
+ * linkmode_resolve_pause - resolve the allowable pause modes
+ * @local_adv: local advertisement in ethtool format
+ * @partner_adv: partner advertisement in ethtool format
+ * @tx_pause: pointer to bool to indicate whether transmit pause should be
+ * enabled.
+ * @rx_pause: pointer to bool to indicate whether receive pause should be
+ * enabled.
+ *
+ * Flow control is resolved according to our and the link partners
+ * advertisements using the following drawn from the 802.3 specs:
+ *  Local device  Link partner
+ *  Pause AsymDir Pause AsymDir Result
+ *    0     X       0     X     Disabled
+ *    0     1       1     0     Disabled
+ *    0     1       1     1     TX
+ *    1     0       0     X     Disabled
+ *    1     X       1     X     TX+RX
+ *    1     1       0     1     RX
+ */
+void linkmode_resolve_pause(const unsigned long *local_adv,
+			    const unsigned long *partner_adv,
+			    bool *tx_pause, bool *rx_pause)
+{
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(m);
+
+	linkmode_and(m, local_adv, partner_adv);
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_Pause_BIT, m)) {
+		*tx_pause = true;
+		*rx_pause = true;
+	} else if (linkmode_test_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, m)) {
+		*tx_pause = linkmode_test_bit(ETHTOOL_LINK_MODE_Pause_BIT,
+					      partner_adv);
+		*rx_pause = linkmode_test_bit(ETHTOOL_LINK_MODE_Pause_BIT,
+					      local_adv);
+	} else {
+		*tx_pause = false;
+		*rx_pause = false;
+	}
+}
+EXPORT_SYMBOL_GPL(linkmode_resolve_pause);
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 28e3c5c0e3c3..651eff5127df 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -2414,6 +2414,32 @@ bool phy_validate_pause(struct phy_device *phydev,
 }
 EXPORT_SYMBOL(phy_validate_pause);
 
+/**
+ * phy_get_pause - resolve negotiated pause modes
+ * @phydev: phy_device struct
+ * @tx_pause: pointer to bool to indicate whether transmit pause should be
+ * enabled.
+ * @rx_pause: pointer to bool to indicate whether receive pause should be
+ * enabled.
+ *
+ * Resolve and return the flow control modes according to the negotiation
+ * result. This includes checking that we are operating in full duplex mode.
+ * See linkmode_resolve_pause() for further details.
+ */
+void phy_get_pause(struct phy_device *phydev, bool *tx_pause, bool *rx_pause)
+{
+	if (phydev->duplex != DUPLEX_FULL) {
+		*tx_pause = false;
+		*rx_pause = false;
+		return;
+	}
+
+	return linkmode_resolve_pause(phydev->advertising,
+				      phydev->lp_advertising,
+				      tx_pause, rx_pause);
+}
+EXPORT_SYMBOL(phy_get_pause);
+
 static bool phy_drv_supports_irq(struct phy_driver *phydrv)
 {
 	return phydrv->config_intr && phydrv->ack_interrupt;
diff --git a/include/linux/linkmode.h b/include/linux/linkmode.h
index 8e5b352e44f2..9ec210f31d06 100644
--- a/include/linux/linkmode.h
+++ b/include/linux/linkmode.h
@@ -88,4 +88,8 @@ static inline int linkmode_subset(const unsigned long *src1,
 	return bitmap_subset(src1, src2, __ETHTOOL_LINK_MODE_MASK_NBITS);
 }
 
+void linkmode_resolve_pause(const unsigned long *local_adv,
+			    const unsigned long *partner_adv,
+			    bool *tx_pause, bool *rx_pause);
+
 #endif /* __LINKMODE_H */
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 452e8ba8665f..118de9f5bbb2 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -1260,6 +1260,9 @@ void phy_set_sym_pause(struct phy_device *phydev, bool rx, bool tx,
 void phy_set_asym_pause(struct phy_device *phydev, bool rx, bool tx);
 bool phy_validate_pause(struct phy_device *phydev,
 			struct ethtool_pauseparam *pp);
+void phy_get_pause(struct phy_device *phydev, bool *tx_pause, bool *rx_pause);
+void phy_resolve_pause(unsigned long *local_adv, unsigned long *partner_adv,
+		       bool *tx_pause, bool *rx_pause);
 
 int phy_register_fixup(const char *bus_id, u32 phy_uid, u32 phy_uid_mask,
 		       int (*run)(struct phy_device *));

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

Add a linkmode helper to set the flow control advertisement in an
ethtool linkmode mask according to the tx/rx capabilities. This
implementation is moved from phylib, and documented with an
analysis of its shortcomings.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/linkmode.c   | 51 ++++++++++++++++++++++++++++++++++++++++++++
 drivers/net/phy/phy_device.c | 17 +--------------
 include/linux/linkmode.h     |  2 ++
 3 files changed, 54 insertions(+), 16 deletions(-)

diff --git a/drivers/net/phy/linkmode.c b/drivers/net/phy/linkmode.c
index 969918795228..f60560fe3499 100644
--- a/drivers/net/phy/linkmode.c
+++ b/drivers/net/phy/linkmode.c
@@ -42,3 +42,54 @@ void linkmode_resolve_pause(const unsigned long *local_adv,
 	}
 }
 EXPORT_SYMBOL_GPL(linkmode_resolve_pause);
+
+/**
+ * linkmode_set_pause - set the pause mode advertisement
+ * @advertisement: advertisement in ethtool format
+ * @tx: boolean from ethtool struct ethtool_pauseparam tx_pause member
+ * @rx: boolean from ethtool struct ethtool_pauseparam rx_pause member
+ *
+ * Configure the advertised Pause and Asym_Pause bits according to the
+ * capabilities of provided in @tx and @rx.
+ *
+ * We convert as follows:
+ *  tx rx  Pause AsymDir
+ *  0  0   0     0
+ *  0  1   1     1
+ *  1  0   0     1
+ *  1  1   1     0
+ *
+ * Note: this translation from ethtool tx/rx notation to the advertisement
+ * is actually very problematical. Here are some examples:
+ *
+ * For tx=0 rx=1, meaning transmit is unsupported, receive is supported:
+ *
+ *  Local device  Link partner
+ *  Pause AsymDir Pause AsymDir Result
+ *    1     1       1     0     TX + RX - but we have no TX support.
+ *    1     1       0     1	Only this gives RX only
+ *
+ * For tx=1 rx=1, meaning we have the capability to transmit and receive
+ * pause frames:
+ *
+ *  Local device  Link partner
+ *  Pause AsymDir Pause AsymDir Result
+ *    1     0       0     1     Disabled - but since we do support tx and rx,
+ *				this should resolve to RX only.
+ *
+ * Hence, asking for:
+ *  rx=1 tx=0 gives Pause+AsymDir advertisement, but we may end up
+ *            resolving to tx+rx pause or only rx pause depending on
+ *            the partners advertisement.
+ *  rx=0 tx=1 gives AsymDir only, which will only give tx pause if
+ *            the partners advertisement allows it.
+ *  rx=1 tx=1 gives Pause only, which will only allow tx+rx pause
+ *            if the other end also advertises Pause.
+ */
+void linkmode_set_pause(unsigned long *advertisement, bool tx, bool rx)
+{
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_Pause_BIT, advertisement, rx);
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, advertisement,
+			 rx ^ tx);
+}
+EXPORT_SYMBOL_GPL(linkmode_set_pause);
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 651eff5127df..022fcc8e7b6f 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -2366,22 +2366,7 @@ void phy_set_asym_pause(struct phy_device *phydev, bool rx, bool tx)
 	__ETHTOOL_DECLARE_LINK_MODE_MASK(oldadv);
 
 	linkmode_copy(oldadv, phydev->advertising);
-
-	linkmode_clear_bit(ETHTOOL_LINK_MODE_Pause_BIT,
-			   phydev->advertising);
-	linkmode_clear_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT,
-			   phydev->advertising);
-
-	if (rx) {
-		linkmode_set_bit(ETHTOOL_LINK_MODE_Pause_BIT,
-				 phydev->advertising);
-		linkmode_set_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT,
-				 phydev->advertising);
-	}
-
-	if (tx)
-		linkmode_change_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT,
-				    phydev->advertising);
+	linkmode_set_pause(phydev->advertising, tx, rx);
 
 	if (!linkmode_equal(oldadv, phydev->advertising) &&
 	    phydev->autoneg)
diff --git a/include/linux/linkmode.h b/include/linux/linkmode.h
index 9ec210f31d06..c664c27a29a0 100644
--- a/include/linux/linkmode.h
+++ b/include/linux/linkmode.h
@@ -92,4 +92,6 @@ void linkmode_resolve_pause(const unsigned long *local_adv,
 			    const unsigned long *partner_adv,
 			    bool *tx_pause, bool *rx_pause);
 
+void linkmode_set_pause(unsigned long *advertisement, bool tx, bool rx);
+
 #endif /* __LINKMODE_H */

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

Remove the ability for ethtool -A to change the pause settings for
fixed links; if this is really required, we can reinstate it later.

Andrew Lunn agrees: "So I think it is safe to not implement ethtool
-A, at least until somebody has a real use case for it."

Lets avoid making things too complex for use cases that aren't being
used.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/phylink.c | 17 +++++------------
 1 file changed, 5 insertions(+), 12 deletions(-)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 6e66b8e77ec7..fa735f451924 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -1379,6 +1379,9 @@ int phylink_ethtool_set_pauseparam(struct phylink *pl,
 
 	ASSERT_RTNL();
 
+	if (pl->cur_link_an_mode == MLO_AN_FIXED)
+		return -EOPNOTSUPP;
+
 	if (!phylink_test(pl->supported, Pause) &&
 	    !phylink_test(pl->supported, Asym_Pause))
 		return -EOPNOTSUPP;
@@ -1405,18 +1408,8 @@ int phylink_ethtool_set_pauseparam(struct phylink *pl,
 				   pause->tx_pause);
 	} else if (!test_bit(PHYLINK_DISABLE_STOPPED,
 			     &pl->phylink_disable_state)) {
-		switch (pl->cur_link_an_mode) {
-		case MLO_AN_FIXED:
-			/* Should we allow fixed links to change against the config? */
-			phylink_resolve_flow(pl, config);
-			phylink_mac_config(pl, config);
-			break;
-
-		case MLO_AN_INBAND:
-			phylink_mac_config(pl, config);
-			phylink_mac_an_restart(pl);
-			break;
-		}
+		phylink_mac_config(pl, &pl->link_config);
+		phylink_mac_an_restart(pl);
 	}
 
 	return 0;

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

Split the application of manually controlled flow control modes from
phylink_resolve_flow(), so that we can use alternative providers of
flow control resolution.

We also want to clear the MLO_PAUSE_AN flag when autoneg is disabled,
since flow control can't be negotiated in this circumstance.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/phylink.c | 42 +++++++++++++++++++++++++-----------------
 1 file changed, 25 insertions(+), 17 deletions(-)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index fa735f451924..1aeb119ec727 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -339,6 +339,18 @@ static int phylink_parse_mode(struct phylink *pl, struct fwnode_handle *fwnode)
 	return 0;
 }
 
+static void phylink_apply_manual_flow(struct phylink *pl,
+				      struct phylink_link_state *state)
+{
+	/* If autoneg is disabled, pause AN is also disabled */
+	if (!state->an_enabled)
+		state->pause &= ~MLO_PAUSE_AN;
+
+	/* Manual configuration of pause modes */
+	if (!(pl->link_config.pause & MLO_PAUSE_AN))
+		state->pause = pl->link_config.pause;
+}
+
 static void phylink_mac_config(struct phylink *pl,
 			       const struct phylink_link_state *state)
 {
@@ -408,25 +420,20 @@ static void phylink_resolve_flow(struct phylink *pl,
 				 struct phylink_link_state *state)
 {
 	int new_pause = 0;
+	int pause = 0;
 
-	if (pl->link_config.pause & MLO_PAUSE_AN) {
-		int pause = 0;
-
-		if (phylink_test(pl->link_config.advertising, Pause))
-			pause |= MLO_PAUSE_SYM;
-		if (phylink_test(pl->link_config.advertising, Asym_Pause))
-			pause |= MLO_PAUSE_ASYM;
+	if (phylink_test(pl->link_config.advertising, Pause))
+		pause |= MLO_PAUSE_SYM;
+	if (phylink_test(pl->link_config.advertising, Asym_Pause))
+		pause |= MLO_PAUSE_ASYM;
 
-		pause &= state->pause;
+	pause &= state->pause;
 
-		if (pause & MLO_PAUSE_SYM)
-			new_pause = MLO_PAUSE_TX | MLO_PAUSE_RX;
-		else if (pause & MLO_PAUSE_ASYM)
-			new_pause = state->pause & MLO_PAUSE_SYM ?
-				 MLO_PAUSE_TX : MLO_PAUSE_RX;
-	} else {
-		new_pause = pl->link_config.pause & MLO_PAUSE_TXRX_MASK;
-	}
+	if (pause & MLO_PAUSE_SYM)
+		new_pause = MLO_PAUSE_TX | MLO_PAUSE_RX;
+	else if (pause & MLO_PAUSE_ASYM)
+		new_pause = state->pause & MLO_PAUSE_SYM ?
+			 MLO_PAUSE_TX : MLO_PAUSE_RX;
 
 	state->pause &= ~MLO_PAUSE_TXRX_MASK;
 	state->pause |= new_pause;
@@ -494,6 +501,7 @@ static void phylink_resolve(struct work_struct *w)
 		case MLO_AN_PHY:
 			link_state = pl->phy_state;
 			phylink_resolve_flow(pl, &link_state);
+			phylink_apply_manual_flow(pl, &link_state);
 			phylink_mac_config_up(pl, &link_state);
 			break;
 
@@ -518,6 +526,7 @@ static void phylink_resolve(struct work_struct *w)
 				 * the pause mode bits. */
 				link_state.pause |= pl->phy_state.pause;
 				phylink_resolve_flow(pl, &link_state);
+				phylink_apply_manual_flow(pl, &link_state);
 				phylink_mac_config(pl, &link_state);
 			}
 			break;
@@ -1012,7 +1021,6 @@ void phylink_start(struct phylink *pl)
 	 * a fixed-link to start with the correct parameters, and also
 	 * ensures that we set the appropriate advertisement for Serdes links.
 	 */
-	phylink_resolve_flow(pl, &pl->link_config);
 	phylink_mac_config(pl, &pl->link_config);
 
 	/* Restart autonegotiation if using 802.3z to ensure that the link

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

Use the new phy_get_pause() helper to get the resolved pause modes for
a PHY rather than resolving the pause modes ourselves. We temporarily
retain our pause mode resolution for causes where there is no PHY
attached, e.g. for fixed-link modes.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/phylink.c | 17 +++++++++--------
 1 file changed, 9 insertions(+), 8 deletions(-)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 1aeb119ec727..c8b5768c2288 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -500,7 +500,6 @@ static void phylink_resolve(struct work_struct *w)
 		switch (pl->cur_link_an_mode) {
 		case MLO_AN_PHY:
 			link_state = pl->phy_state;
-			phylink_resolve_flow(pl, &link_state);
 			phylink_apply_manual_flow(pl, &link_state);
 			phylink_mac_config_up(pl, &link_state);
 			break;
@@ -523,9 +522,8 @@ static void phylink_resolve(struct work_struct *w)
 				link_state.interface = pl->phy_state.interface;
 
 				/* If we have a PHY, we need to update with
-				 * the pause mode bits. */
-				link_state.pause |= pl->phy_state.pause;
-				phylink_resolve_flow(pl, &link_state);
+				 * the PHY flow control bits. */
+				link_state.pause = pl->phy_state.pause;
 				phylink_apply_manual_flow(pl, &link_state);
 				phylink_mac_config(pl, &link_state);
 			}
@@ -714,15 +712,18 @@ static void phylink_phy_change(struct phy_device *phydev, bool up,
 			       bool do_carrier)
 {
 	struct phylink *pl = phydev->phylink;
+	bool tx_pause, rx_pause;
+
+	phy_get_pause(phydev, &tx_pause, &rx_pause);
 
 	mutex_lock(&pl->state_mutex);
 	pl->phy_state.speed = phydev->speed;
 	pl->phy_state.duplex = phydev->duplex;
 	pl->phy_state.pause = MLO_PAUSE_NONE;
-	if (phydev->pause)
-		pl->phy_state.pause |= MLO_PAUSE_SYM;
-	if (phydev->asym_pause)
-		pl->phy_state.pause |= MLO_PAUSE_ASYM;
+	if (tx_pause)
+		pl->phy_state.pause |= MLO_PAUSE_TX;
+	if (rx_pause)
+		pl->phy_state.pause |= MLO_PAUSE_RX;
 	pl->phy_state.interface = phydev->interface;
 	pl->phy_state.link = up;
 	mutex_unlock(&pl->state_mutex);

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

Resolve the fixed link flow control using the recently introduced
linkmode_resolve_pause() helper, which we use in
phylink_get_fixed_state() only when operating in full duplex mode.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/phylink.c | 70 +++++++++++++++++++++--------------------------
 include/linux/phylink.h   |  8 ++----
 2 files changed, 34 insertions(+), 44 deletions(-)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index c8b5768c2288..4a3aa022f12f 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -181,9 +181,11 @@ static int phylink_parse_fixedlink(struct phylink *pl,
 		/* We treat the "pause" and "asym-pause" terminology as
 		 * defining the link partner's ability. */
 		if (fwnode_property_read_bool(fixed_node, "pause"))
-			pl->link_config.pause |= MLO_PAUSE_SYM;
+			__set_bit(ETHTOOL_LINK_MODE_Pause_BIT,
+				  pl->link_config.lp_advertising);
 		if (fwnode_property_read_bool(fixed_node, "asym-pause"))
-			pl->link_config.pause |= MLO_PAUSE_ASYM;
+			__set_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT,
+				  pl->link_config.lp_advertising);
 
 		if (ret == 0) {
 			desc = fwnode_gpiod_get_index(fixed_node, "link", 0,
@@ -215,9 +217,11 @@ static int phylink_parse_fixedlink(struct phylink *pl,
 						DUPLEX_FULL : DUPLEX_HALF;
 			pl->link_config.speed = prop[2];
 			if (prop[3])
-				pl->link_config.pause |= MLO_PAUSE_SYM;
+				__set_bit(ETHTOOL_LINK_MODE_Pause_BIT,
+					  pl->link_config.lp_advertising);
 			if (prop[4])
-				pl->link_config.pause |= MLO_PAUSE_ASYM;
+				__set_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT,
+					  pl->link_config.lp_advertising);
 		}
 	}
 
@@ -351,6 +355,22 @@ static void phylink_apply_manual_flow(struct phylink *pl,
 		state->pause = pl->link_config.pause;
 }
 
+static void phylink_resolve_flow(struct phylink_link_state *state)
+{
+	bool tx_pause, rx_pause;
+
+	state->pause = MLO_PAUSE_NONE;
+	if (state->duplex == DUPLEX_FULL) {
+		linkmode_resolve_pause(state->advertising,
+				       state->lp_advertising,
+				       &tx_pause, &rx_pause);
+		if (tx_pause)
+			state->pause |= MLO_PAUSE_TX;
+		if (rx_pause)
+			state->pause |= MLO_PAUSE_RX;
+	}
+}
+
 static void phylink_mac_config(struct phylink *pl,
 			       const struct phylink_link_state *state)
 {
@@ -399,44 +419,16 @@ static void phylink_mac_pcs_get_state(struct phylink *pl,
 /* The fixed state is... fixed except for the link state,
  * which may be determined by a GPIO or a callback.
  */
-static void phylink_get_fixed_state(struct phylink *pl, struct phylink_link_state *state)
+static void phylink_get_fixed_state(struct phylink *pl,
+				    struct phylink_link_state *state)
 {
 	*state = pl->link_config;
 	if (pl->get_fixed_state)
 		pl->get_fixed_state(pl->netdev, state);
 	else if (pl->link_gpio)
 		state->link = !!gpiod_get_value_cansleep(pl->link_gpio);
-}
 
-/* Flow control is resolved according to our and the link partners
- * advertisements using the following drawn from the 802.3 specs:
- *  Local device  Link partner
- *  Pause AsymDir Pause AsymDir Result
- *    1     X       1     X     TX+RX
- *    0     1       1     1     TX
- *    1     1       0     1     RX
- */
-static void phylink_resolve_flow(struct phylink *pl,
-				 struct phylink_link_state *state)
-{
-	int new_pause = 0;
-	int pause = 0;
-
-	if (phylink_test(pl->link_config.advertising, Pause))
-		pause |= MLO_PAUSE_SYM;
-	if (phylink_test(pl->link_config.advertising, Asym_Pause))
-		pause |= MLO_PAUSE_ASYM;
-
-	pause &= state->pause;
-
-	if (pause & MLO_PAUSE_SYM)
-		new_pause = MLO_PAUSE_TX | MLO_PAUSE_RX;
-	else if (pause & MLO_PAUSE_ASYM)
-		new_pause = state->pause & MLO_PAUSE_SYM ?
-			 MLO_PAUSE_TX : MLO_PAUSE_RX;
-
-	state->pause &= ~MLO_PAUSE_TXRX_MASK;
-	state->pause |= new_pause;
+	phylink_resolve_flow(state);
 }
 
 static const char *phylink_pause_to_str(int pause)
@@ -1399,8 +1391,7 @@ int phylink_ethtool_set_pauseparam(struct phylink *pl,
 	    !pause->autoneg && pause->rx_pause != pause->tx_pause)
 		return -EINVAL;
 
-	config->pause &= ~(MLO_PAUSE_AN | MLO_PAUSE_TXRX_MASK);
-
+	config->pause = 0;
 	if (pause->autoneg)
 		config->pause |= MLO_PAUSE_AN;
 	if (pause->rx_pause)
@@ -1511,13 +1502,14 @@ static int phylink_mii_emul_read(unsigned int reg,
 				 struct phylink_link_state *state)
 {
 	struct fixed_phy_status fs;
+	unsigned long *lpa = state->lp_advertising;
 	int val;
 
 	fs.link = state->link;
 	fs.speed = state->speed;
 	fs.duplex = state->duplex;
-	fs.pause = state->pause & MLO_PAUSE_SYM;
-	fs.asym_pause = state->pause & MLO_PAUSE_ASYM;
+	fs.pause = test_bit(ETHTOOL_LINK_MODE_Pause_BIT, lpa);
+	fs.asym_pause = test_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, lpa);
 
 	val = swphy_read_reg(reg, &fs);
 	if (reg == MII_BMSR) {
diff --git a/include/linux/phylink.h b/include/linux/phylink.h
index 523209e70947..0d6073c2b2b7 100644
--- a/include/linux/phylink.h
+++ b/include/linux/phylink.h
@@ -12,12 +12,10 @@ struct net_device;
 
 enum {
 	MLO_PAUSE_NONE,
-	MLO_PAUSE_ASYM = BIT(0),
-	MLO_PAUSE_SYM = BIT(1),
-	MLO_PAUSE_RX = BIT(2),
-	MLO_PAUSE_TX = BIT(3),
+	MLO_PAUSE_RX = BIT(0),
+	MLO_PAUSE_TX = BIT(1),
 	MLO_PAUSE_TXRX_MASK = MLO_PAUSE_TX | MLO_PAUSE_RX,
-	MLO_PAUSE_AN = BIT(4),
+	MLO_PAUSE_AN = BIT(2),
 
 	MLO_AN_PHY = 0,	/* Conventional PHY */
 	MLO_AN_FIXED,	/* Fixed-link mode */

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

When ethtool -A is used to change the pause modes, the pause
advertisement is not being changed, but the documentation in
uapi/linux/ethtool.h says we should be. Add that capability to
phylink.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/phylink.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 4a3aa022f12f..3b45f9aa6fbe 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -1391,6 +1391,7 @@ int phylink_ethtool_set_pauseparam(struct phylink *pl,
 	    !pause->autoneg && pause->rx_pause != pause->tx_pause)
 		return -EINVAL;
 
+	mutex_lock(&pl->state_mutex);
 	config->pause = 0;
 	if (pause->autoneg)
 		config->pause |= MLO_PAUSE_AN;
@@ -1399,6 +1400,22 @@ int phylink_ethtool_set_pauseparam(struct phylink *pl,
 	if (pause->tx_pause)
 		config->pause |= MLO_PAUSE_TX;
 
+	/*
+	 * See the comments for linkmode_set_pause(), wrt the deficiencies
+	 * with the current implementation.  A solution to this issue would
+	 * be:
+	 * ethtool  Local device
+	 *  rx  tx  Pause AsymDir
+	 *  0   0   0     0
+	 *  1   0   1     1
+	 *  0   1   0     1
+	 *  1   1   1     1
+	 * and then use the ethtool rx/tx enablement status to mask the
+	 * rx/tx pause resolution.
+	 */
+	linkmode_set_pause(config->advertising, pause->tx_pause,
+			   pause->rx_pause);
+
 	/* If we have a PHY, phylib will call our link state function if the
 	 * mode has changed, which will trigger a resolve and update the MAC
 	 * configuration.
@@ -1411,6 +1428,7 @@ int phylink_ethtool_set_pauseparam(struct phylink *pl,
 		phylink_mac_config(pl, &pl->link_config);
 		phylink_mac_an_restart(pl);
 	}
+	mutex_unlock(&pl->state_mutex);
 
 	return 0;
 }

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

Improve the initial MAC configuration so we get a configuration which
more represents the final operating mode, in particular with respect
to the flow control settings.

We do this by:
1) more fully initialising our phy state, so we can use this as the
   initial state for PHY based connections.
2) reading the fixed link state.
3) ensuring that in-band mode has sane pause settings for SGMII vs
   802.3z negotiation modes.

In all three cases, we ensure that state->link is false, just in case
any MAC drivers have other ideas by mis-using this member, and we also
take account of manual pause mode configuration at this point.

This avoids MLO_PAUSE_AN being seen in mac_config() when operating in
PHY, fixed mode or inband SGMII mode, thereby giving cleaner semantics
to the pause flags.  As a result of this, the pause flags now indicate
in a mode-independent way what is required from a mac_config()
implementation.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/phylink.c | 36 ++++++++++++++++++++++++++++++++++--
 1 file changed, 34 insertions(+), 2 deletions(-)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 3b45f9aa6fbe..a5ca934ea12e 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -431,6 +431,35 @@ static void phylink_get_fixed_state(struct phylink *pl,
 	phylink_resolve_flow(state);
 }
 
+static void phylink_mac_initial_config(struct phylink *pl)
+{
+	struct phylink_link_state link_state;
+
+	switch (pl->cur_link_an_mode) {
+	case MLO_AN_PHY:
+		link_state = pl->phy_state;
+		break;
+
+	case MLO_AN_FIXED:
+		phylink_get_fixed_state(pl, &link_state);
+		break;
+
+	case MLO_AN_INBAND:
+		link_state = pl->link_config;
+		if (link_state.interface == PHY_INTERFACE_MODE_SGMII)
+			link_state.pause = MLO_PAUSE_NONE;
+		break;
+
+	default: /* can't happen */
+		return;
+	}
+
+	link_state.link = false;
+
+	phylink_apply_manual_flow(pl, &link_state);
+	phylink_mac_config(pl, &link_state);
+}
+
 static const char *phylink_pause_to_str(int pause)
 {
 	switch (pause & MLO_PAUSE_TXRX_MASK) {
@@ -785,6 +814,9 @@ static int phylink_bringup_phy(struct phylink *pl, struct phy_device *phy,
 	mutex_lock(&pl->state_mutex);
 	pl->phydev = phy;
 	pl->phy_state.interface = interface;
+	pl->phy_state.pause = MLO_PAUSE_NONE;
+	pl->phy_state.speed = SPEED_UNKNOWN;
+	pl->phy_state.duplex = DUPLEX_UNKNOWN;
 	linkmode_copy(pl->supported, supported);
 	linkmode_copy(pl->link_config.advertising, config.advertising);
 
@@ -1014,7 +1046,7 @@ void phylink_start(struct phylink *pl)
 	 * a fixed-link to start with the correct parameters, and also
 	 * ensures that we set the appropriate advertisement for Serdes links.
 	 */
-	phylink_mac_config(pl, &pl->link_config);
+	phylink_mac_initial_config(pl);
 
 	/* Restart autonegotiation if using 802.3z to ensure that the link
 	 * parameters are properly negotiated.  This is necessary for DSA
@@ -1832,7 +1864,7 @@ static int phylink_sfp_config(struct phylink *pl, u8 mode,
 
 	if (changed && !test_bit(PHYLINK_DISABLE_STOPPED,
 				 &pl->phylink_disable_state))
-		phylink_mac_config(pl, &pl->link_config);
+		phylink_mac_initial_config(pl);
 
 	return ret;
 }

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

Clarify the expected flow control settings operation in the phylink
documentation for each negotiation mode.

Signed-off-by: Russell King <[email-masked]>
---
 include/linux/phylink.h | 26 ++++++++++++++++++--------
 1 file changed, 18 insertions(+), 8 deletions(-)

diff --git a/include/linux/phylink.h b/include/linux/phylink.h
index 0d6073c2b2b7..812357c03df4 100644
--- a/include/linux/phylink.h
+++ b/include/linux/phylink.h
@@ -152,13 +152,20 @@ void mac_pcs_get_state(struct phylink_config *config,
  * guaranteed to be correct, and so any mac_config() implementation must
  * never reference these fields.
  *
+ * In all negotiation modes, as defined by @mode, @state->pause indicates the
+ * pause settings which should be applied as follows. If %MLO_PAUSE_AN is not
+ * set, %MLO_PAUSE_TX and %MLO_PAUSE_RX indicate whether the MAC should send
+ * pause frames and/or act on received pause frames respectively. Otherwise,
+ * the results of in-band negotiation/status from the MAC PCS should be used
+ * to control the MAC pause mode settings.
+ *
  * The action performed depends on the currently selected mode:
  *
  * %MLO_AN_FIXED, %MLO_AN_PHY:
- *   Configure the specified @state->speed, @state->duplex and
- *   @state->pause (%MLO_PAUSE_TX / %MLO_PAUSE_RX) modes over a link
- *   specified by @state->interface.  @state->advertising may be used,
- *   but is not required.  Other members of @state must be ignored.
+ *   Configure the specified @state->speed and @state->duplex over a link
+ *   specified by @state->interface. @state->advertising may be used, but
+ *   is not required. Pause modes as above. Other members of @state must
+ *   be ignored.
  *
  *   Valid state members: interface, speed, duplex, pause, advertising.
  *
@@ -170,11 +177,14 @@ void mac_pcs_get_state(struct phylink_config *config,
  *   mac_pcs_get_state() callback. Changes in link state must be made
  *   by calling phylink_mac_change().
  *
+ *   Interface mode specific details are mentioned below.
+ *
  *   If in 802.3z mode, the link speed is fixed, dependent on the
- *   @state->interface. Duplex is negotiated, and pause is advertised
- *   according to @state->an_enabled, @state->pause and
- *   @state->advertising flags. Beware of MACs which only support full
- *   duplex at gigabit and higher speeds.
+ *   @state->interface. Duplex and pause modes are negotiated via
+ *   the in-band configuration word. Advertised pause modes are set
+ *   according to the @state->an_enabled and @state->advertising
+ *   flags. Beware of MACs which only support full duplex at gigabit
+ *   and higher speeds.
  *
  *   If in Cisco SGMII mode, the link speed and duplex mode are passed
  *   in the serial bitstream 16-bit configuration word, and the MAC

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

Now that the phylib module loading issue has been resolved, we can
allow this PHY driver to be built as a module.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/Kconfig | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 9dabe03a668c..edb1cb8a228e 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -326,8 +326,8 @@ config BROADCOM_PHY
 	  BCM5481, BCM54810 and BCM5482 PHYs.
 
 config BCM84881_PHY
-	bool "Broadcom BCM84881 PHY"
-	depends on PHYLIB=y
+	tristate "Broadcom BCM84881 PHY"
+	depends on PHYLIB
 	---help---
 	  Support the Broadcom BCM84881 PHY.

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

When configuring a tree of independent bridges, propagating changes
from the upper bridge across a bridge master to the lower bridge
ports brings surprises.

For example, a lower bridge may have vlan filtering enabled.  It
may have a vlan interface attached to the bridge master, which may
then be incorporated into another bridge.  As soon as the lower
bridge vlan interface is attached to the upper bridge, the lower
bridge has vlan filtering disabled.

This occurs because switchdev recursively applies its changes to
all lower devices no matter what.

Reviewed-by: Ido Schimmel <[email-masked]>
Tested-by: Ido Schimmel <[email-masked]>
Signed-off-by: Russell King <[email-masked]>
---
 net/switchdev/switchdev.c | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/net/switchdev/switchdev.c b/net/switchdev/switchdev.c
index 3a1d428c1336..d881e5e4a889 100644
--- a/net/switchdev/switchdev.c
+++ b/net/switchdev/switchdev.c
@@ -475,6 +475,9 @@ static int __switchdev_handle_port_obj_add(struct net_device *dev,
 	 * necessary to go through this helper.
 	 */
 	netdev_for_each_lower_dev(dev, lower_dev, iter) {
+		if (netif_is_bridge_master(lower_dev))
+			continue;
+
 		err = __switchdev_handle_port_obj_add(lower_dev, port_obj_info,
 						      check_cb, add_cb);
 		if (err && err != -EOPNOTSUPP)
@@ -526,6 +529,9 @@ static int __switchdev_handle_port_obj_del(struct net_device *dev,
 	 * necessary to go through this helper.
 	 */
 	netdev_for_each_lower_dev(dev, lower_dev, iter) {
+		if (netif_is_bridge_master(lower_dev))
+			continue;
+
 		err = __switchdev_handle_port_obj_del(lower_dev, port_obj_info,
 						      check_cb, del_cb);
 		if (err && err != -EOPNOTSUPP)
@@ -576,6 +582,9 @@ static int __switchdev_handle_port_attr_set(struct net_device *dev,
 	 * necessary to go through this helper.
 	 */
 	netdev_for_each_lower_dev(dev, lower_dev, iter) {
+		if (netif_is_bridge_master(lower_dev))
+			continue;
+
 		err = __switchdev_handle_port_attr_set(lower_dev, port_attr_info,
 						       check_cb, set_cb);
 		if (err && err != -EOPNOTSUPP)

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

When setting VLANs on DSA switches, the VLAN is added to both the port
concerned as well as the CPU port by dsa_slave_vlan_add(), as well as
any DSA ports.  If multiple ports are configured with the same VLAN ID,
this triggers a warning on the CPU and DSA ports.

Avoid this warning for CPU and DSA ports.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/dsa/mv88e6xxx/chip.c | 12 +++++++++---
 1 file changed, 9 insertions(+), 3 deletions(-)

diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
index 2f993e673ec7..7ab41fe67c1b 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.c
+++ b/drivers/net/dsa/mv88e6xxx/chip.c
@@ -1785,7 +1785,7 @@ static int mv88e6xxx_broadcast_setup(struct mv88e6xxx_chip *chip, u16 vid)
 }
 
 static int mv88e6xxx_port_vlan_join(struct mv88e6xxx_chip *chip, int port,
-				    u16 vid, u8 member)
+				    u16 vid, u8 member, bool warn)
 {
 	const u8 non_member = MV88E6XXX_G1_VTU_DATA_MEMBER_TAG_NON_MEMBER;
 	struct mv88e6xxx_vtu_entry vlan;
@@ -1830,7 +1830,7 @@ static int mv88e6xxx_port_vlan_join(struct mv88e6xxx_chip *chip, int port,
 		err = mv88e6xxx_vtu_loadpurge(chip, &vlan);
 		if (err)
 			return err;
-	} else {
+	} else if (warn) {
 		dev_info(chip->dev, "p%d: already a member of VLAN %d\n",
 			 port, vid);
 	}
@@ -1844,6 +1844,7 @@ static void mv88e6xxx_port_vlan_add(struct dsa_switch *ds, int port,
 	struct mv88e6xxx_chip *chip = ds->priv;
 	bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED;
 	bool pvid = vlan->flags & BRIDGE_VLAN_INFO_PVID;
+	bool warn;
 	u8 member;
 	u16 vid;
 
@@ -1857,10 +1858,15 @@ static void mv88e6xxx_port_vlan_add(struct dsa_switch *ds, int port,
 	else
 		member = MV88E6XXX_G1_VTU_DATA_MEMBER_TAG_TAGGED;
 
+	/* net/dsa/slave.c will call dsa_port_vlan_add() for the affected port
+	 * and then the CPU port. Do not warn for duplicates for the CPU port.
+	 */
+	warn = !dsa_is_cpu_port(ds, port) && !dsa_is_dsa_port(ds, port);
+
 	mv88e6xxx_reg_lock(chip);
 
 	for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid)
-		if (mv88e6xxx_port_vlan_join(chip, port, vid, member))
+		if (mv88e6xxx_port_vlan_join(chip, port, vid, member, warn))
 			dev_err(ds->dev, "p%d: failed to add VLAN %d%c\n", port,
 				vid, untagged ? 'u' : 't');

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

Read the copper autonegotiation results from the copper specific
status register, rather than decoding the advertisements. Reading
what the link is actually doing will allow us to support downshift
modes.

Reviewed-by: Andrew Lunn <[email-masked]>
Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/marvell10g.c | 141 +++++++++++++++++++++++++++----------------
 1 file changed, 89 insertions(+), 52 deletions(-)

diff --git a/drivers/net/phy/marvell10g.c b/drivers/net/phy/marvell10g.c
index 64c9f3bba2cd..9a4e12a2af07 100644
--- a/drivers/net/phy/marvell10g.c
+++ b/drivers/net/phy/marvell10g.c
@@ -39,10 +39,19 @@ enum {
 	MV_PCS_BASE_R		= 0x1000,
 	MV_PCS_1000BASEX	= 0x2000,
 
-	MV_PCS_PAIRSWAP		= 0x8182,
-	MV_PCS_PAIRSWAP_MASK	= 0x0003,
-	MV_PCS_PAIRSWAP_AB	= 0x0002,
-	MV_PCS_PAIRSWAP_NONE	= 0x0003,
+	MV_PCS_CSSR1		= 0x8008,
+	MV_PCS_CSSR1_SPD1_MASK	= 0xc000,
+	MV_PCS_CSSR1_SPD1_SPD2	= 0xc000,
+	MV_PCS_CSSR1_SPD1_1000	= 0x8000,
+	MV_PCS_CSSR1_SPD1_100	= 0x4000,
+	MV_PCS_CSSR1_SPD1_10	= 0x0000,
+	MV_PCS_CSSR1_DUPLEX_FULL= BIT(13),
+	MV_PCS_CSSR1_RESOLVED	= BIT(11),
+	MV_PCS_CSSR1_MDIX	= BIT(6),
+	MV_PCS_CSSR1_SPD2_MASK	= 0x000c,
+	MV_PCS_CSSR1_SPD2_5000	= 0x0008,
+	MV_PCS_CSSR1_SPD2_2500	= 0x0004,
+	MV_PCS_CSSR1_SPD2_10000	= 0x0000,
 
 	/* These registers appear at 0x800X and 0xa00X - the 0xa00X control
 	 * registers appear to set themselves to the 0x800X when AN is
@@ -413,35 +422,18 @@ static void mv3310_update_interface(struct phy_device *phydev)
 }
 
 /* 10GBASE-ER,LR,LRM,SR do not support autonegotiation. */
-static int mv3310_read_10gbr_status(struct phy_device *phydev)
+static int mv3310_read_status_10gbaser(struct phy_device *phydev)
 {
 	phydev->link = 1;
 	phydev->speed = SPEED_10000;
 	phydev->duplex = DUPLEX_FULL;
 
-	mv3310_update_interface(phydev);
-
 	return 0;
 }
 
-static int mv3310_read_status(struct phy_device *phydev)
+static int mv3310_read_status_copper(struct phy_device *phydev)
 {
-	int val;
-
-	phydev->speed = SPEED_UNKNOWN;
-	phydev->duplex = DUPLEX_UNKNOWN;
-	linkmode_zero(phydev->lp_advertising);
-	phydev->link = 0;
-	phydev->pause = 0;
-	phydev->asym_pause = 0;
-	phydev->mdix = 0;
-
-	val = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_PCS_BASE_R + MDIO_STAT1);
-	if (val < 0)
-		return val;
-
-	if (val & MDIO_STAT1_LSTATUS)
-		return mv3310_read_10gbr_status(phydev);
+	int cssr1, speed, val;
 
 	val = genphy_c45_read_link(phydev);
 	if (val < 0)
@@ -451,6 +443,52 @@ static int mv3310_read_status(struct phy_device *phydev)
 	if (val < 0)
 		return val;
 
+	cssr1 = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_PCS_CSSR1);
+	if (cssr1 < 0)
+		return val;
+
+	/* If the link settings are not resolved, mark the link down */
+	if (!(cssr1 & MV_PCS_CSSR1_RESOLVED)) {
+		phydev->link = 0;
+		return 0;
+	}
+
+	/* Read the copper link settings */
+	speed = cssr1 & MV_PCS_CSSR1_SPD1_MASK;
+	if (speed == MV_PCS_CSSR1_SPD1_SPD2)
+		speed |= cssr1 & MV_PCS_CSSR1_SPD2_MASK;
+
+	switch (speed) {
+	case MV_PCS_CSSR1_SPD1_SPD2 | MV_PCS_CSSR1_SPD2_10000:
+		phydev->speed = SPEED_10000;
+		break;
+
+	case MV_PCS_CSSR1_SPD1_SPD2 | MV_PCS_CSSR1_SPD2_5000:
+		phydev->speed = SPEED_5000;
+		break;
+
+	case MV_PCS_CSSR1_SPD1_SPD2 | MV_PCS_CSSR1_SPD2_2500:
+		phydev->speed = SPEED_2500;
+		break;
+
+	case MV_PCS_CSSR1_SPD1_1000:
+		phydev->speed = SPEED_1000;
+		break;
+
+	case MV_PCS_CSSR1_SPD1_100:
+		phydev->speed = SPEED_100;
+		break;
+
+	case MV_PCS_CSSR1_SPD1_10:
+		phydev->speed = SPEED_10;
+		break;
+	}
+
+	phydev->duplex = cssr1 & MV_PCS_CSSR1_DUPLEX_FULL ?
+			 DUPLEX_FULL : DUPLEX_HALF;
+	phydev->mdix = cssr1 & MV_PCS_CSSR1_MDIX ?
+		       ETH_TP_MDI_X : ETH_TP_MDI;
+
 	if (val & MDIO_AN_STAT1_COMPLETE) {
 		val = genphy_c45_read_lpa(phydev);
 		if (val < 0)
@@ -463,39 +501,38 @@ static int mv3310_read_status(struct phy_device *phydev)
 
 		mii_stat1000_mod_linkmode_lpa_t(phydev->lp_advertising, val);
 
-		if (phydev->autoneg == AUTONEG_ENABLE)
-			phy_resolve_aneg_linkmode(phydev);
+		/* Update the pause status */
+		phy_resolve_aneg_pause(phydev);
 	}
 
-	if (phydev->autoneg != AUTONEG_ENABLE) {
-		val = genphy_c45_read_pma(phydev);
-		if (val < 0)
-			return val;
-	}
+	return 0;
+}
 
-	if (phydev->speed == SPEED_10000) {
-		val = genphy_c45_read_mdix(phydev);
-		if (val < 0)
-			return val;
-	} else {
-		val = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_PCS_PAIRSWAP);
-		if (val < 0)
-			return val;
+static int mv3310_read_status(struct phy_device *phydev)
+{
+	int err, val;
 
-		switch (val & MV_PCS_PAIRSWAP_MASK) {
-		case MV_PCS_PAIRSWAP_AB:
-			phydev->mdix = ETH_TP_MDI_X;
-			break;
-		case MV_PCS_PAIRSWAP_NONE:
-			phydev->mdix = ETH_TP_MDI;
-			break;
-		default:
-			phydev->mdix = ETH_TP_MDI_INVALID;
-			break;
-		}
-	}
+	phydev->speed = SPEED_UNKNOWN;
+	phydev->duplex = DUPLEX_UNKNOWN;
+	linkmode_zero(phydev->lp_advertising);
+	phydev->link = 0;
+	phydev->pause = 0;
+	phydev->asym_pause = 0;
+	phydev->mdix = ETH_TP_MDI_INVALID;
 
-	mv3310_update_interface(phydev);
+	val = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_PCS_BASE_R + MDIO_STAT1);
+	if (val < 0)
+		return val;
+
+	if (val & MDIO_STAT1_LSTATUS)
+		err = mv3310_read_status_10gbaser(phydev);
+	else
+		err = mv3310_read_status_copper(phydev);
+	if (err < 0)
+		return err;
+
+	if (phydev->link)
+		mv3310_update_interface(phydev);
 
 	return 0;
 }

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

Add support for the MII ioctl API.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c b/drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c
index 7ff147e89426..b6c46639aa4c 100644
--- a/drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c
+++ b/drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c
@@ -1704,10 +1704,15 @@ static int dpaa2_eth_ts_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
 
 static int dpaa2_eth_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
 {
+	struct dpaa2_eth_priv *priv = netdev_priv(dev);
+
 	if (cmd == SIOCSHWTSTAMP)
 		return dpaa2_eth_ts_ioctl(dev, rq, cmd);
 
-	return -EINVAL;
+	if (priv->mac)
+		return phylink_mii_ioctl(priv->mac->phylink, rq, cmd);
+
+	return -EOPNOTSUPP;
 }
 
 static bool xdp_mtu_valid(struct dpaa2_eth_priv *priv, int mtu)

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

Add support for ethtool -r so that PHY negotiation can be restarted.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/ethernet/freescale/dpaa2/dpaa2-ethtool.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/drivers/net/ethernet/freescale/dpaa2/dpaa2-ethtool.c b/drivers/net/ethernet/freescale/dpaa2/dpaa2-ethtool.c
index 96676abcebd5..94347c695233 100644
--- a/drivers/net/ethernet/freescale/dpaa2/dpaa2-ethtool.c
+++ b/drivers/net/ethernet/freescale/dpaa2/dpaa2-ethtool.c
@@ -79,6 +79,16 @@ static void dpaa2_eth_get_drvinfo(struct net_device *net_dev,
 		sizeof(drvinfo->bus_info));
 }
 
+static int dpaa2_eth_nway_reset(struct net_device *net_dev)
+{
+	struct dpaa2_eth_priv *priv = netdev_priv(net_dev);
+
+	if (priv->mac)
+		return phylink_ethtool_nway_reset(priv->mac->phylink);
+
+	return -EOPNOTSUPP;
+}
+
 static int
 dpaa2_eth_get_link_ksettings(struct net_device *net_dev,
 			     struct ethtool_link_ksettings *link_settings)
@@ -761,6 +771,7 @@ static int dpaa2_eth_get_ts_info(struct net_device *dev,
 
 const struct ethtool_ops dpaa2_ethtool_ops = {
 	.get_drvinfo = dpaa2_eth_get_drvinfo,
+	.nway_reset = dpaa2_eth_nway_reset,
 	.get_link = ethtool_op_get_link,
 	.get_link_ksettings = dpaa2_eth_get_link_ksettings,
 	.set_link_ksettings = dpaa2_eth_set_link_ksettings,

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

Propagate the resolved link parameters via the mac_link_up() call for
MACs that do not automatically track their PCS state. We propagate the
link parameters via function arguments so that inappropriate members
of struct phylink_link_state can't be accessed, and creating a new
structure just for this adds needless complexity to the API.

Tested-by: Andre Przywara <[email-masked]>
Tested-by: Alexandre Belloni <[email-masked]>
Tested-by: Vladimir Oltean <[email-masked]>
Signed-off-by: Russell King <[email-masked]>
---
 Documentation/networking/sfp-phylink.rst          | 17 +++++--
 drivers/net/ethernet/cadence/macb_main.c          |  7 ++-
 drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c  |  7 ++-
 drivers/net/ethernet/marvell/mvneta.c             |  8 ++--
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c   | 19 +++++---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c       |  7 +--
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c |  4 +-
 drivers/net/ethernet/xilinx/xilinx_axienet_main.c |  7 +--
 drivers/net/phy/phylink.c                         |  9 +++-
 include/linux/phylink.h                           | 57 +++++++++++++++++------
 net/dsa/port.c                                    |  4 +-
 11 files changed, 105 insertions(+), 41 deletions(-)

diff --git a/Documentation/networking/sfp-phylink.rst b/Documentation/networking/sfp-phylink.rst
index d753a309f9d1..8d7af28cd835 100644
--- a/Documentation/networking/sfp-phylink.rst
+++ b/Documentation/networking/sfp-phylink.rst
@@ -74,10 +74,13 @@ phylib to the sfp/phylink support.  Please send patches to improve
 this documentation.
 
 1. Optionally split the network driver's phylib update function into
-   three parts dealing with link-down, link-up and reconfiguring the
-   MAC settings. This can be done as a separate preparation commit.
+   two parts dealing with link-down and link-up. This can be done as
+   a separate preparation commit.
 
-   An example of this preparation can be found in git commit fc548b991fb0.
+   An older example of this preparation can be found in git commit
+   fc548b991fb0, although this was splitting into three parts; the
+   link-up part now includes configuring the MAC for the link settings.
+   Please see :c:func:`mac_link_up` for more information on this.
 
 2. Replace::
 
@@ -207,6 +210,14 @@ this documentation.
    using. This is particularly important for in-band negotiation
    methods such as 1000base-X and SGMII.
 
+   The :c:func:`mac_link_up` method is used to inform the MAC that the
+   link has come up. The call includes the negotiation mode and interface
+   for reference only. The finalised link parameters are also supplied
+   (speed, duplex and flow control/pause enablement settings) which
+   should be used to configure the MAC when the MAC and PCS are not
+   tightly integrated, or when the settings are not coming from in-band
+   negotiation.
+
    The :c:func:`mac_config` method is used to update the MAC with the
    requested state, and must avoid unnecessarily taking the link down
    when making changes to the MAC configuration.  This means the
diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
index 2c28da1737fe..7ab0bef5e1bd 100644
--- a/drivers/net/ethernet/cadence/macb_main.c
+++ b/drivers/net/ethernet/cadence/macb_main.c
@@ -626,8 +626,11 @@ static void macb_mac_link_down(struct phylink_config *config, unsigned int mode,
 	netif_tx_stop_all_queues(ndev);
 }
 
-static void macb_mac_link_up(struct phylink_config *config, unsigned int mode,
-			     phy_interface_t interface, struct phy_device *phy)
+static void macb_mac_link_up(struct phylink_config *config,
+			     struct phy_device *phy,
+			     unsigned int mode, phy_interface_t interface,
+			     int speed, int duplex,
+			     bool tx_pause, bool rx_pause)
 {
 	struct net_device *ndev = to_net_dev(config->dev);
 	struct macb *bp = netdev_priv(ndev);
diff --git a/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c b/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c
index 84233e467ed1..3a75c5b58f95 100644
--- a/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c
+++ b/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c
@@ -154,8 +154,11 @@ static void dpaa2_mac_config(struct phylink_config *config, unsigned int mode,
 		netdev_err(mac->net_dev, "dpmac_set_link_state() = %d\n", err);
 }
 
-static void dpaa2_mac_link_up(struct phylink_config *config, unsigned int mode,
-			      phy_interface_t interface, struct phy_device *phy)
+static void dpaa2_mac_link_up(struct phylink_config *config,
+			      struct phy_device *phy,
+			      unsigned int mode, phy_interface_t interface,
+			      int speed, int duplex,
+			      bool tx_pause, bool rx_pause)
 {
 	struct dpaa2_mac *mac = phylink_to_dpaa2_mac(config);
 	struct dpmac_link_state *dpmac_state = &mac->state;
diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c
index 11babc79dc6c..cc6ab9028bca 100644
--- a/drivers/net/ethernet/marvell/mvneta.c
+++ b/drivers/net/ethernet/marvell/mvneta.c
@@ -3901,9 +3901,11 @@ static void mvneta_mac_link_down(struct phylink_config *config,
 	mvneta_set_eee(pp, false);
 }
 
-static void mvneta_mac_link_up(struct phylink_config *config, unsigned int mode,
-			       phy_interface_t interface,
-			       struct phy_device *phy)
+static void mvneta_mac_link_up(struct phylink_config *config,
+			       struct phy_device *phy,
+			       unsigned int mode, phy_interface_t interface,
+			       int speed, int duplex,
+			       bool tx_pause, bool rx_pause)
 {
 	struct net_device *ndev = to_net_dev(config->dev);
 	struct mvneta_port *pp = netdev_priv(ndev);
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 72133cbe55d4..ed8042d97e29 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -58,8 +58,11 @@ static struct {
  */
 static void mvpp2_mac_config(struct phylink_config *config, unsigned int mode,
 			     const struct phylink_link_state *state);
-static void mvpp2_mac_link_up(struct phylink_config *config, unsigned int mode,
-			      phy_interface_t interface, struct phy_device *phy);
+static void mvpp2_mac_link_up(struct phylink_config *config,
+			      struct phy_device *phy,
+			      unsigned int mode, phy_interface_t interface,
+			      int speed, int duplex,
+			      bool tx_pause, bool rx_pause);
 
 /* Queue modes */
 #define MVPP2_QDIST_SINGLE_MODE	0
@@ -3473,8 +3476,9 @@ static void mvpp2_start_dev(struct mvpp2_port *port)
 			.interface = port->phy_interface,
 		};
 		mvpp2_mac_config(&port->phylink_config, MLO_AN_INBAND, &state);
-		mvpp2_mac_link_up(&port->phylink_config, MLO_AN_INBAND,
-				  port->phy_interface, NULL);
+		mvpp2_mac_link_up(&port->phylink_config, NULL,
+				  MLO_AN_INBAND, port->phy_interface,
+				  SPEED_UNKNOWN, DUPLEX_UNKNOWN, false, false);
 	}
 
 	netif_tx_start_all_queues(port->dev);
@@ -5141,8 +5145,11 @@ static void mvpp2_mac_config(struct phylink_config *config, unsigned int mode,
 	mvpp2_port_enable(port);
 }
 
-static void mvpp2_mac_link_up(struct phylink_config *config, unsigned int mode,
-			      phy_interface_t interface, struct phy_device *phy)
+static void mvpp2_mac_link_up(struct phylink_config *config,
+			      struct phy_device *phy,
+			      unsigned int mode, phy_interface_t interface,
+			      int speed, int duplex,
+			      bool tx_pause, bool rx_pause)
 {
 	struct net_device *dev = to_net_dev(config->dev);
 	struct mvpp2_port *port = netdev_priv(dev);
diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
index 8c6cfd15481c..8d28f90acfe7 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
@@ -412,9 +412,10 @@ static void mtk_mac_link_down(struct phylink_config *config, unsigned int mode,
 	mtk_w32(mac->hw, mcr, MTK_MAC_MCR(mac->id));
 }
 
-static void mtk_mac_link_up(struct phylink_config *config, unsigned int mode,
-			    phy_interface_t interface,
-			    struct phy_device *phy)
+static void mtk_mac_link_up(struct phylink_config *config,
+			    struct phy_device *phy,
+			    unsigned int mode, phy_interface_t interface,
+			    int speed, int duplex, bool tx_pause, bool rx_pause)
 {
 	struct mtk_mac *mac = container_of(config, struct mtk_mac,
 					   phylink_config);
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 7da18c9afa01..d5abdc616b4d 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -950,8 +950,10 @@ static void stmmac_mac_link_down(struct phylink_config *config,
 }
 
 static void stmmac_mac_link_up(struct phylink_config *config,
+			       struct phy_device *phy,
 			       unsigned int mode, phy_interface_t interface,
-			       struct phy_device *phy)
+			       int speed, int duplex,
+			       bool tx_pause, bool rx_pause)
 {
 	struct stmmac_priv *priv = netdev_priv(to_net_dev(config->dev));
 
diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
index 20746b801959..197740781157 100644
--- a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
+++ b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
@@ -1486,9 +1486,10 @@ static void axienet_mac_link_down(struct phylink_config *config,
 }
 
 static void axienet_mac_link_up(struct phylink_config *config,
-				unsigned int mode,
-				phy_interface_t interface,
-				struct phy_device *phy)
+				struct phy_device *phy,
+				unsigned int mode, phy_interface_t interface,
+				int speed, int duplex,
+				bool tx_pause, bool rx_pause)
 {
 	/* nothing meaningful to do */
 }
diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index a5ca934ea12e..5347275215be 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -480,8 +480,11 @@ static void phylink_mac_link_up(struct phylink *pl,
 	struct net_device *ndev = pl->netdev;
 
 	pl->cur_interface = link_state.interface;
-	pl->ops->mac_link_up(pl->config, pl->cur_link_an_mode,
-			     pl->cur_interface, pl->phydev);
+	pl->ops->mac_link_up(pl->config, pl->phydev,
+			     pl->cur_link_an_mode, pl->cur_interface,
+			     link_state.speed, link_state.duplex,
+			     !!(link_state.pause & MLO_PAUSE_TX),
+			     !!(link_state.pause & MLO_PAUSE_RX));
 
 	if (ndev)
 		netif_carrier_on(ndev);
@@ -547,6 +550,8 @@ static void phylink_resolve(struct work_struct *w)
 				link_state.pause = pl->phy_state.pause;
 				phylink_apply_manual_flow(pl, &link_state);
 				phylink_mac_config(pl, &link_state);
+			} else {
+				phylink_apply_manual_flow(pl, &link_state);
 			}
 			break;
 		}
diff --git a/include/linux/phylink.h b/include/linux/phylink.h
index 812357c03df4..2180eb1aa254 100644
--- a/include/linux/phylink.h
+++ b/include/linux/phylink.h
@@ -91,9 +91,10 @@ struct phylink_mac_ops {
 	void (*mac_an_restart)(struct phylink_config *config);
 	void (*mac_link_down)(struct phylink_config *config, unsigned int mode,
 			      phy_interface_t interface);
-	void (*mac_link_up)(struct phylink_config *config, unsigned int mode,
-			    phy_interface_t interface,
-			    struct phy_device *phy);
+	void (*mac_link_up)(struct phylink_config *config,
+			    struct phy_device *phy, unsigned int mode,
+			    phy_interface_t interface, int speed, int duplex,
+			    bool tx_pause, bool rx_pause);
 };
 
 #if 0 /* For kernel-doc purposes only. */
@@ -152,6 +153,9 @@ void mac_pcs_get_state(struct phylink_config *config,
  * guaranteed to be correct, and so any mac_config() implementation must
  * never reference these fields.
  *
+ * (this requires a rewrite - please refer to mac_link_up() for situations
+ *  where the PCS and MAC are not tightly integrated.)
+ *
  * In all negotiation modes, as defined by @mode, @state->pause indicates the
  * pause settings which should be applied as follows. If %MLO_PAUSE_AN is not
  * set, %MLO_PAUSE_TX and %MLO_PAUSE_RX indicate whether the MAC should send
@@ -162,12 +166,20 @@ void mac_pcs_get_state(struct phylink_config *config,
  * The action performed depends on the currently selected mode:
  *
  * %MLO_AN_FIXED, %MLO_AN_PHY:
- *   Configure the specified @state->speed and @state->duplex over a link
- *   specified by @state->interface. @state->advertising may be used, but
- *   is not required. Pause modes as above. Other members of @state must
- *   be ignored.
+ *   Configure for non-inband negotiation mode, where the link settings
+ *   are completely communicated via mac_link_up().  The physical link
+ *   protocol from the MAC is specified by @state->interface.
+ *
+ *   @state->advertising may be used, but is not required.
+ *
+ *   Older drivers (prior to the mac_link_up() change) may use @state->speed,
+ *   @state->duplex and @state->pause to configure the MAC, but this is
+ *   deprecated; such drivers should be converted to use mac_link_up().
  *
- *   Valid state members: interface, speed, duplex, pause, advertising.
+ *   Other members of @state must be ignored.
+ *
+ *   Valid state members: interface, advertising.
+ *   Deprecated state members: speed, duplex, pause.
  *
  * %MLO_AN_INBAND:
  *   place the link in an inband negotiation mode (such as 802.3z
@@ -228,19 +240,34 @@ void mac_link_down(struct phylink_config *config, unsigned int mode,
 /**
  * mac_link_up() - allow the link to come up
  * @config: a pointer to a &struct phylink_config.
+ * @phy: any attached phy
  * @mode: link autonegotiation mode
  * @interface: link &typedef phy_interface_t mode
- * @phy: any attached phy
+ * @speed: link speed
+ * @duplex: link duplex
+ * @tx_pause: link transmit pause enablement status
+ * @rx_pause: link receive pause enablement status
  *
- * If @mode is not an in-band negotiation mode (as defined by
- * phylink_autoneg_inband()), allow the link to come up. If @phy
- * is non-%NULL, configure Energy Efficient Ethernet by calling
+ * Configure the MAC for an established link.
+ *
+ * @speed, @duplex, @tx_pause and @rx_pause indicate the finalised link
+ * settings, and should be used to configure the MAC block appropriately
+ * where these settings are not automatically conveyed from the PCS block,
+ * or if in-band negotiation (as defined by phylink_autoneg_inband(@mode))
+ * is disabled.
+ *
+ * Note that when 802.3z in-band negotiation is in use, it is possible
+ * that the user wishes to override the pause settings, and this should
+ * be allowed when considering the implementation of this method.
+ *
+ * If in-band negotiation mode is disabled, allow the link to come up. If
+ * @phy is non-%NULL, configure Energy Efficient Ethernet by calling
  * phy_init_eee() and perform appropriate MAC configuration for EEE.
  * Interface type selection must be done in mac_config().
  */
-void mac_link_up(struct phylink_config *config, unsigned int mode,
-		 phy_interface_t interface,
-		 struct phy_device *phy);
+void mac_link_up(struct phylink_config *config, struct phy_device *phy,
+		 unsigned int mode, phy_interface_t interface,
+		 int speed, int duplex, bool tx_pause, bool rx_pause);
 #endif
 
 struct phylink *phylink_create(struct phylink_config *, struct fwnode_handle *,
diff --git a/net/dsa/port.c b/net/dsa/port.c
index ec13dc666788..bd67ec610198 100644
--- a/net/dsa/port.c
+++ b/net/dsa/port.c
@@ -513,9 +513,11 @@ static void dsa_port_phylink_mac_link_down(struct phylink_config *config,
 }
 
 static void dsa_port_phylink_mac_link_up(struct phylink_config *config,
+					 struct phy_device *phydev,
 					 unsigned int mode,
 					 phy_interface_t interface,
-					 struct phy_device *phydev)
+					 int speed, int duplex,
+					 bool tx_pause, bool rx_pause)
 {
 	struct dsa_port *dp = container_of(config, struct dsa_port, pl_config);
 	struct dsa_switch *ds = dp->ds;

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

Propagate the resolved link configuration down via DSA's
phylink_mac_link_up() operation to allow split PCS/MAC to work.

Tested-by: Vladimir Oltean <[email-masked]>
Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/dsa/b53/b53_common.c       | 4 +++-
 drivers/net/dsa/b53/b53_priv.h         | 4 +++-
 drivers/net/dsa/bcm_sf2.c              | 4 +++-
 drivers/net/dsa/lantiq_gswip.c         | 4 +++-
 drivers/net/dsa/mt7530.c               | 4 +++-
 drivers/net/dsa/mv88e6xxx/chip.c       | 4 +++-
 drivers/net/dsa/sja1105/sja1105_main.c | 4 +++-
 include/net/dsa.h                      | 4 +++-
 net/dsa/port.c                         | 3 ++-
 9 files changed, 26 insertions(+), 9 deletions(-)

diff --git a/drivers/net/dsa/b53/b53_common.c b/drivers/net/dsa/b53/b53_common.c
index 1a69286daa8d..ceafce446317 100644
--- a/drivers/net/dsa/b53/b53_common.c
+++ b/drivers/net/dsa/b53/b53_common.c
@@ -1289,7 +1289,9 @@ EXPORT_SYMBOL(b53_phylink_mac_link_down);
 void b53_phylink_mac_link_up(struct dsa_switch *ds, int port,
 			     unsigned int mode,
 			     phy_interface_t interface,
-			     struct phy_device *phydev)
+			     struct phy_device *phydev,
+			     int speed, int duplex,
+			     bool tx_pause, bool rx_pause)
 {
 	struct b53_device *dev = ds->priv;
 
diff --git a/drivers/net/dsa/b53/b53_priv.h b/drivers/net/dsa/b53/b53_priv.h
index 3c30f3a7eb29..3d42318bc3f1 100644
--- a/drivers/net/dsa/b53/b53_priv.h
+++ b/drivers/net/dsa/b53/b53_priv.h
@@ -338,7 +338,9 @@ void b53_phylink_mac_link_down(struct dsa_switch *ds, int port,
 void b53_phylink_mac_link_up(struct dsa_switch *ds, int port,
 			     unsigned int mode,
 			     phy_interface_t interface,
-			     struct phy_device *phydev);
+			     struct phy_device *phydev,
+			     int speed, int duplex,
+			     bool tx_pause, bool rx_pause);
 int b53_vlan_filtering(struct dsa_switch *ds, int port, bool vlan_filtering);
 int b53_vlan_prepare(struct dsa_switch *ds, int port,
 		     const struct switchdev_obj_port_vlan *vlan);
diff --git a/drivers/net/dsa/bcm_sf2.c b/drivers/net/dsa/bcm_sf2.c
index b0f5280a83cb..368ead87e07a 100644
--- a/drivers/net/dsa/bcm_sf2.c
+++ b/drivers/net/dsa/bcm_sf2.c
@@ -648,7 +648,9 @@ static void bcm_sf2_sw_mac_link_down(struct dsa_switch *ds, int port,
 static void bcm_sf2_sw_mac_link_up(struct dsa_switch *ds, int port,
 				   unsigned int mode,
 				   phy_interface_t interface,
-				   struct phy_device *phydev)
+				   struct phy_device *phydev,
+				   int speed, int duplex,
+				   bool tx_pause, bool rx_pause)
 {
 	struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds);
 	struct ethtool_eee *p = &priv->dev->ports[port].eee;
diff --git a/drivers/net/dsa/lantiq_gswip.c b/drivers/net/dsa/lantiq_gswip.c
index 0369c22fe3e1..cf6fa8fede33 100644
--- a/drivers/net/dsa/lantiq_gswip.c
+++ b/drivers/net/dsa/lantiq_gswip.c
@@ -1517,7 +1517,9 @@ static void gswip_phylink_mac_link_down(struct dsa_switch *ds, int port,
 static void gswip_phylink_mac_link_up(struct dsa_switch *ds, int port,
 				      unsigned int mode,
 				      phy_interface_t interface,
-				      struct phy_device *phydev)
+				      struct phy_device *phydev,
+				      int speed, int duplex,
+				      bool tx_pause, bool rx_pause)
 {
 	struct gswip_priv *priv = ds->priv;
 
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 7cbd1bd4c5a6..056686a8fdb6 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -1482,7 +1482,9 @@ static void mt7530_phylink_mac_link_down(struct dsa_switch *ds, int port,
 static void mt7530_phylink_mac_link_up(struct dsa_switch *ds, int port,
 				       unsigned int mode,
 				       phy_interface_t interface,
-				       struct phy_device *phydev)
+				       struct phy_device *phydev,
+				       int speed, int duplex,
+				       bool tx_pause, bool rx_pause)
 {
 	struct mt7530_priv *priv = ds->priv;
 
diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
index 7ab41fe67c1b..d1f78642ecc1 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.c
+++ b/drivers/net/dsa/mv88e6xxx/chip.c
@@ -655,7 +655,9 @@ static void mv88e6xxx_mac_link_down(struct dsa_switch *ds, int port,
 
 static void mv88e6xxx_mac_link_up(struct dsa_switch *ds, int port,
 				  unsigned int mode, phy_interface_t interface,
-				  struct phy_device *phydev)
+				  struct phy_device *phydev,
+				  int speed, int duplex,
+				  bool tx_pause, bool rx_pause)
 {
 	if (mode == MLO_AN_FIXED)
 		mv88e6xxx_mac_link_force(ds, port, LINK_FORCED_UP);
diff --git a/drivers/net/dsa/sja1105/sja1105_main.c b/drivers/net/dsa/sja1105/sja1105_main.c
index 7edea5741a5f..a3709f7ad0e2 100644
--- a/drivers/net/dsa/sja1105/sja1105_main.c
+++ b/drivers/net/dsa/sja1105/sja1105_main.c
@@ -786,7 +786,9 @@ static void sja1105_mac_link_down(struct dsa_switch *ds, int port,
 static void sja1105_mac_link_up(struct dsa_switch *ds, int port,
 				unsigned int mode,
 				phy_interface_t interface,
-				struct phy_device *phydev)
+				struct phy_device *phydev,
+				int speed, int duplex,
+				bool tx_pause, bool rx_pause)
 {
 	sja1105_inhibit_tx(ds->priv, BIT(port), false);
 }
diff --git a/include/net/dsa.h b/include/net/dsa.h
index 63495e3443ac..7d3d84f0ef42 100644
--- a/include/net/dsa.h
+++ b/include/net/dsa.h
@@ -420,7 +420,9 @@ struct dsa_switch_ops {
 	void	(*phylink_mac_link_up)(struct dsa_switch *ds, int port,
 				       unsigned int mode,
 				       phy_interface_t interface,
-				       struct phy_device *phydev);
+				       struct phy_device *phydev,
+				       int speed, int duplex,
+				       bool tx_pause, bool rx_pause);
 	void	(*phylink_fixed_state)(struct dsa_switch *ds, int port,
 				       struct phylink_link_state *state);
 	/*
diff --git a/net/dsa/port.c b/net/dsa/port.c
index bd67ec610198..e6875d8f944d 100644
--- a/net/dsa/port.c
+++ b/net/dsa/port.c
@@ -528,7 +528,8 @@ static void dsa_port_phylink_mac_link_up(struct phylink_config *config,
 		return;
 	}
 
-	ds->ops->phylink_mac_link_up(ds, dp->index, mode, interface, phydev);
+	ds->ops->phylink_mac_link_up(ds, dp->index, mode, interface, phydev,
+				     speed, duplex, tx_pause, rx_pause);
 }
 
 const struct phylink_mac_ops dsa_port_phylink_mac_ops = {

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

Use the resolved link configuration to set the MAC configuration when
mac_link_up() for non-internal-PHY ports.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/dsa/mv88e6xxx/chip.c | 75 +++++++++++++++++++++++++++++++---------
 1 file changed, 59 insertions(+), 16 deletions(-)

diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
index d1f78642ecc1..cbf67e92efb2 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.c
+++ b/drivers/net/dsa/mv88e6xxx/chip.c
@@ -632,25 +632,30 @@ static void mv88e6xxx_mac_config(struct dsa_switch *ds, int port,
 		dev_err(ds->dev, "p%d: failed to configure MAC\n", port);
 }
 
-static void mv88e6xxx_mac_link_force(struct dsa_switch *ds, int port, int link)
+static void mv88e6xxx_mac_link_down(struct dsa_switch *ds, int port,
+				    unsigned int mode,
+				    phy_interface_t interface)
 {
 	struct mv88e6xxx_chip *chip = ds->priv;
-	int err;
+	const struct mv88e6xxx_ops *ops;
+	int err = 0;
 
-	mv88e6xxx_reg_lock(chip);
-	err = chip->info->ops->port_set_link(chip, port, link);
-	mv88e6xxx_reg_unlock(chip);
+	ops = chip->info->ops;
 
-	if (err)
-		dev_err(chip->dev, "p%d: failed to force MAC link\n", port);
-}
+	/* Internal PHYs propagate their configuration directly to the MAC.
+	 * External PHYs depend on whether the PPU is enabled for this port.
+	 * FIXME: we should be using the PPU enable state here. What about
+	 * an automedia port?
+	 */
+	if (!mv88e6xxx_phy_is_internal(ds, port) && ops->port_set_link) {
+		mv88e6xxx_reg_lock(chip);
+		err = ops->port_set_link(chip, port, LINK_FORCED_DOWN);
+		mv88e6xxx_reg_unlock(chip);
 
-static void mv88e6xxx_mac_link_down(struct dsa_switch *ds, int port,
-				    unsigned int mode,
-				    phy_interface_t interface)
-{
-	if (mode == MLO_AN_FIXED)
-		mv88e6xxx_mac_link_force(ds, port, LINK_FORCED_DOWN);
+		if (err)
+			dev_err(chip->dev,
+				"p%d: failed to force MAC link down\n", port);
+	}
 }
 
 static void mv88e6xxx_mac_link_up(struct dsa_switch *ds, int port,
@@ -659,8 +664,46 @@ static void mv88e6xxx_mac_link_up(struct dsa_switch *ds, int port,
 				  int speed, int duplex,
 				  bool tx_pause, bool rx_pause)
 {
-	if (mode == MLO_AN_FIXED)
-		mv88e6xxx_mac_link_force(ds, port, LINK_FORCED_UP);
+	struct mv88e6xxx_chip *chip = ds->priv;
+	const struct mv88e6xxx_ops *ops;
+	int err = 0;
+
+	ops = chip->info->ops;
+
+	/* Internal PHYs propagate their configuration directly to the MAC.
+	 * External PHYs depend on whether the PPU is enabled for this port.
+	 * FIXME: we should be using the PPU enable state here. What about
+	 * an automedia port?
+	 */
+	if (!mv88e6xxx_phy_is_internal(ds, port)) {
+		mv88e6xxx_reg_lock(chip);
+		/* FIXME: for an automedia port, should we force the link
+		 * down here - what if the link comes up due to "other" media
+		 * while we're bringing the port up, how is the exclusivity
+		 * handled in the Marvell hardware? E.g. port 4 on 88E6532
+		 * shared between internal PHY and Serdes.
+		 */
+		if (ops->port_set_speed) {
+			err = ops->port_set_speed(chip, port, speed);
+			if (err && err != -EOPNOTSUPP)
+				goto error;
+		}
+
+		if (ops->port_set_duplex) {
+			err = ops->port_set_duplex(chip, port, duplex);
+			if (err && err != -EOPNOTSUPP)
+				goto error;
+		}
+
+		if (ops->port_set_link)
+			err = ops->port_set_link(chip, port, LINK_FORCED_UP);
+error:
+		mv88e6xxx_reg_unlock(chip);
+
+		if (err && err != -EOPNOTSUPP)
+			dev_err(ds->dev,
+				"p%d: failed to configure MAC link up\n", port);
+	}
 }
 
 static int mv88e6xxx_stats_snapshot(struct mv88e6xxx_chip *chip, int port)

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

Convert the Xilinx AXI ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().

Tested-by: Andre Przywara <[email-masked]>
Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/ethernet/xilinx/xilinx_axienet_main.c | 38 +++++++++++------------
 1 file changed, 19 insertions(+), 19 deletions(-)

diff --git a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
index 197740781157..c2f4c5ca2e80 100644
--- a/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
+++ b/drivers/net/ethernet/xilinx/xilinx_axienet_main.c
@@ -1440,6 +1440,22 @@ static void axienet_mac_an_restart(struct phylink_config *config)
 
 static void axienet_mac_config(struct phylink_config *config, unsigned int mode,
 			       const struct phylink_link_state *state)
+{
+	/* nothing meaningful to do */
+}
+
+static void axienet_mac_link_down(struct phylink_config *config,
+				  unsigned int mode,
+				  phy_interface_t interface)
+{
+	/* nothing meaningful to do */
+}
+
+static void axienet_mac_link_up(struct phylink_config *config,
+				struct phy_device *phy,
+				unsigned int mode, phy_interface_t interface,
+				int speed, int duplex,
+				bool tx_pause, bool rx_pause)
 {
 	struct net_device *ndev = to_net_dev(config->dev);
 	struct axienet_local *lp = netdev_priv(ndev);
@@ -1448,7 +1464,7 @@ static void axienet_mac_config(struct phylink_config *config, unsigned int mode,
 	emmc_reg = axienet_ior(lp, XAE_EMMC_OFFSET);
 	emmc_reg &= ~XAE_EMMC_LINKSPEED_MASK;
 
-	switch (state->speed) {
+	switch (speed) {
 	case SPEED_1000:
 		emmc_reg |= XAE_EMMC_LINKSPD_1000;
 		break;
@@ -1467,33 +1483,17 @@ static void axienet_mac_config(struct phylink_config *config, unsigned int mode,
 	axienet_iow(lp, XAE_EMMC_OFFSET, emmc_reg);
 
 	fcc_reg = axienet_ior(lp, XAE_FCC_OFFSET);
-	if (state->pause & MLO_PAUSE_TX)
+	if (tx_pause)
 		fcc_reg |= XAE_FCC_FCTX_MASK;
 	else
 		fcc_reg &= ~XAE_FCC_FCTX_MASK;
-	if (state->pause & MLO_PAUSE_RX)
+	if (rx_pause)
 		fcc_reg |= XAE_FCC_FCRX_MASK;
 	else
 		fcc_reg &= ~XAE_FCC_FCRX_MASK;
 	axienet_iow(lp, XAE_FCC_OFFSET, fcc_reg);
 }
 
-static void axienet_mac_link_down(struct phylink_config *config,
-				  unsigned int mode,
-				  phy_interface_t interface)
-{
-	/* nothing meaningful to do */
-}
-
-static void axienet_mac_link_up(struct phylink_config *config,
-				struct phy_device *phy,
-				unsigned int mode, phy_interface_t interface,
-				int speed, int duplex,
-				bool tx_pause, bool rx_pause)
-{
-	/* nothing meaningful to do */
-}
-
 static const struct phylink_mac_ops axienet_phylink_ops = {
 	.validate = axienet_validate,
 	.mac_pcs_get_state = axienet_mac_pcs_get_state,

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:01 +0100

Convert the DPAA2 ethernet driver to use the finalised link parameters
in mac_link_up() rather than the parameters in mac_config(), which are
more suited to the needs of the DPAA2 MC firmware than those available
via mac_config().

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c | 54 ++++++++++++++----------
 drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.h |  1 +
 2 files changed, 33 insertions(+), 22 deletions(-)

diff --git a/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c b/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c
index 3a75c5b58f95..3ee236c5fc37 100644
--- a/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c
+++ b/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c
@@ -123,35 +123,16 @@ static void dpaa2_mac_config(struct phylink_config *config, unsigned int mode,
 	struct dpmac_link_state *dpmac_state = &mac->state;
 	int err;
 
-	if (state->speed != SPEED_UNKNOWN)
-		dpmac_state->rate = state->speed;
-
-	if (state->duplex != DUPLEX_UNKNOWN) {
-		if (!state->duplex)
-			dpmac_state->options |= DPMAC_LINK_OPT_HALF_DUPLEX;
-		else
-			dpmac_state->options &= ~DPMAC_LINK_OPT_HALF_DUPLEX;
-	}
-
 	if (state->an_enabled)
 		dpmac_state->options |= DPMAC_LINK_OPT_AUTONEG;
 	else
 		dpmac_state->options &= ~DPMAC_LINK_OPT_AUTONEG;
 
-	if (state->pause & MLO_PAUSE_RX)
-		dpmac_state->options |= DPMAC_LINK_OPT_PAUSE;
-	else
-		dpmac_state->options &= ~DPMAC_LINK_OPT_PAUSE;
-
-	if (!!(state->pause & MLO_PAUSE_RX) ^ !!(state->pause & MLO_PAUSE_TX))
-		dpmac_state->options |= DPMAC_LINK_OPT_ASYM_PAUSE;
-	else
-		dpmac_state->options &= ~DPMAC_LINK_OPT_ASYM_PAUSE;
-
 	err = dpmac_set_link_state(mac->mc_io, 0,
 				   mac->mc_dev->mc_handle, dpmac_state);
 	if (err)
-		netdev_err(mac->net_dev, "dpmac_set_link_state() = %d\n", err);
+		netdev_err(mac->net_dev, "%s: dpmac_set_link_state() = %d\n",
+			   __func__, err);
 }
 
 static void dpaa2_mac_link_up(struct phylink_config *config,
@@ -165,10 +146,37 @@ static void dpaa2_mac_link_up(struct phylink_config *config,
 	int err;
 
 	dpmac_state->up = 1;
+
+	if (mac->if_link_type == DPMAC_LINK_TYPE_PHY) {
+		/* If the DPMAC is configured for PHY mode, we need
+		 * to pass the link parameters to the MC firmware.
+		 */
+		dpmac_state->rate = speed;
+
+		if (duplex == DUPLEX_HALF)
+			dpmac_state->options |= DPMAC_LINK_OPT_HALF_DUPLEX;
+		else if (duplex == DUPLEX_FULL)
+			dpmac_state->options &= ~DPMAC_LINK_OPT_HALF_DUPLEX;
+
+		/* This is lossy; the firmware really should take the pause
+		 * enablement status rather than pause/asym pause status.
+		 */
+		if (rx_pause)
+			dpmac_state->options |= DPMAC_LINK_OPT_PAUSE;
+		else
+			dpmac_state->options &= ~DPMAC_LINK_OPT_PAUSE;
+
+		if (rx_pause ^ tx_pause)
+			dpmac_state->options |= DPMAC_LINK_OPT_ASYM_PAUSE;
+		else
+			dpmac_state->options &= ~DPMAC_LINK_OPT_ASYM_PAUSE;
+	}
+
 	err = dpmac_set_link_state(mac->mc_io, 0,
 				   mac->mc_dev->mc_handle, dpmac_state);
 	if (err)
-		netdev_err(mac->net_dev, "dpmac_set_link_state() = %d\n", err);
+		netdev_err(mac->net_dev, "%s: dpmac_set_link_state() = %d\n",
+			   __func__, err);
 }
 
 static void dpaa2_mac_link_down(struct phylink_config *config,
@@ -241,6 +249,8 @@ int dpaa2_mac_connect(struct dpaa2_mac *mac)
 		goto err_close_dpmac;
 	}
 
+	mac->if_link_type = attr.link_type;
+
 	dpmac_node = dpaa2_mac_get_node(attr.id);
 	if (!dpmac_node) {
 		netdev_err(net_dev, "No dpmac@%d node found.\n", attr.id);
diff --git a/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.h b/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.h
index 4da8079b9155..2130d9c7d40e 100644
--- a/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.h
+++ b/drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.h
@@ -20,6 +20,7 @@ struct dpaa2_mac {
 	struct phylink_config phylink_config;
 	struct phylink *phylink;
 	phy_interface_t if_mode;
+	enum dpmac_link_type if_link_type;
 };
 
 bool dpaa2_mac_is_type_fixed(struct fsl_mc_device *dpmac_dev,

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Convert the macb ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().

Tested-by: Alexandre Belloni <[email-masked]>
Signed-off-by: Russell King <[email-masked]>
---
Updated patch from Alexandre Belloni <[email-masked]>
that depends on ac2fcfa9fd26 ("net: macb: Properly handle phylink on
at91rm9200").
---
 drivers/net/ethernet/cadence/macb.h      |  1 -
 drivers/net/ethernet/cadence/macb_main.c | 50 ++++++++++++++++++--------------
 2 files changed, 29 insertions(+), 22 deletions(-)

diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h
index a3f0f27fc79a..ab827fb4b6b9 100644
--- a/drivers/net/ethernet/cadence/macb.h
+++ b/drivers/net/ethernet/cadence/macb.h
@@ -1200,7 +1200,6 @@ struct macb {
 	unsigned int		dma_burst_length;
 
 	phy_interface_t		phy_interface;
-	int			speed;
 
 	/* AT91RM9200 transmit */
 	struct sk_buff *skb;			/* holds skb until xmit interrupt completes */
diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
index 7ab0bef5e1bd..3a7c26b08607 100644
--- a/drivers/net/ethernet/cadence/macb_main.c
+++ b/drivers/net/ethernet/cadence/macb_main.c
@@ -571,37 +571,20 @@ static void macb_mac_config(struct phylink_config *config, unsigned int mode,
 
 	old_ctrl = ctrl = macb_or_gem_readl(bp, NCFGR);
 
-	/* Clear all the bits we might set later */
-	ctrl &= ~(MACB_BIT(SPD) | MACB_BIT(FD) | MACB_BIT(PAE));
-
 	if (bp->caps & MACB_CAPS_MACB_IS_EMAC) {
 		if (state->interface == PHY_INTERFACE_MODE_RMII)
 			ctrl |= MACB_BIT(RM9200_RMII);
 	} else {
-		ctrl &= ~(GEM_BIT(GBE) | GEM_BIT(SGMIIEN) | GEM_BIT(PCSSEL));
-
-		/* We do not support MLO_PAUSE_RX yet */
-		if (state->pause & MLO_PAUSE_TX)
-			ctrl |= MACB_BIT(PAE);
+		ctrl &= ~(GEM_BIT(SGMIIEN) | GEM_BIT(PCSSEL));
 
 		if (state->interface == PHY_INTERFACE_MODE_SGMII)
 			ctrl |= GEM_BIT(SGMIIEN) | GEM_BIT(PCSSEL);
 	}
 
-	if (state->speed == SPEED_1000)
-		ctrl |= GEM_BIT(GBE);
-	else if (state->speed == SPEED_100)
-		ctrl |= MACB_BIT(SPD);
-
-	if (state->duplex)
-		ctrl |= MACB_BIT(FD);
-
 	/* Apply the new configuration, if any */
 	if (old_ctrl ^ ctrl)
 		macb_or_gem_writel(bp, NCFGR, ctrl);
 
-	bp->speed = state->speed;
-
 	spin_unlock_irqrestore(&bp->lock, flags);
 }
 
@@ -635,10 +618,33 @@ static void macb_mac_link_up(struct phylink_config *config,
 	struct net_device *ndev = to_net_dev(config->dev);
 	struct macb *bp = netdev_priv(ndev);
 	struct macb_queue *queue;
+	unsigned long flags;
 	unsigned int q;
+	u32 ctrl;
+
+	spin_lock_irqsave(&bp->lock, flags);
+
+	ctrl = macb_or_gem_readl(bp, NCFGR);
+
+	ctrl &= ~(MACB_BIT(SPD) | MACB_BIT(FD));
+
+	if (speed == SPEED_100)
+		ctrl |= MACB_BIT(SPD);
+
+	if (duplex)
+		ctrl |= MACB_BIT(FD);
 
 	if (!(bp->caps & MACB_CAPS_MACB_IS_EMAC)) {
-		macb_set_tx_clk(bp->tx_clk, bp->speed, ndev);
+		ctrl &= ~(GEM_BIT(GBE) | MACB_BIT(PAE));
+
+		if (speed == SPEED_1000)
+			ctrl |= GEM_BIT(GBE);
+
+		/* We do not support MLO_PAUSE_RX yet */
+		if (tx_pause)
+			ctrl |= MACB_BIT(PAE);
+
+		macb_set_tx_clk(bp->tx_clk, speed, ndev);
 
 		/* Initialize rings & buffers as clearing MACB_BIT(TE) in link down
 		 * cleared the pipeline and control registers.
@@ -651,6 +657,10 @@ static void macb_mac_link_up(struct phylink_config *config,
 				     bp->rx_intr_mask | MACB_TX_INT_FLAGS | MACB_BIT(HRESP));
 	}
 
+	macb_or_gem_writel(bp, NCFGR, ctrl);
+
+	spin_unlock_irqrestore(&bp->lock, flags);
+
 	/* Enable Rx and Tx */
 	macb_writel(bp, NCR, macb_readl(bp, NCR) | MACB_BIT(RE) | MACB_BIT(TE));
 
@@ -4432,8 +4442,6 @@ static int macb_probe(struct platform_device *pdev)
 	else
 		bp->phy_interface = interface;
 
-	bp->speed = SPEED_UNKNOWN;
-
 	/* IP specific init */
 	err = init(pdev);
 	if (err)

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Convert the Marvell mvneta ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/ethernet/marvell/mvneta.c | 55 ++++++++++++++++++++++++-----------
 1 file changed, 38 insertions(+), 17 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c
index cc6ab9028bca..ae0ee12e724e 100644
--- a/drivers/net/ethernet/marvell/mvneta.c
+++ b/drivers/net/ethernet/marvell/mvneta.c
@@ -3766,13 +3766,9 @@ static void mvneta_mac_config(struct phylink_config *config, unsigned int mode,
 	new_clk = gmac_clk & ~MVNETA_GMAC_1MS_CLOCK_ENABLE;
 	new_an = gmac_an & ~(MVNETA_GMAC_INBAND_AN_ENABLE |
 			     MVNETA_GMAC_INBAND_RESTART_AN |
-			     MVNETA_GMAC_CONFIG_MII_SPEED |
-			     MVNETA_GMAC_CONFIG_GMII_SPEED |
 			     MVNETA_GMAC_AN_SPEED_EN |
 			     MVNETA_GMAC_ADVERT_SYM_FLOW_CTRL |
-			     MVNETA_GMAC_CONFIG_FLOW_CTRL |
 			     MVNETA_GMAC_AN_FLOW_CTRL_EN |
-			     MVNETA_GMAC_CONFIG_FULL_DUPLEX |
 			     MVNETA_GMAC_AN_DUPLEX_EN);
 
 	/* Even though it might look weird, when we're configured in
@@ -3787,24 +3783,20 @@ static void mvneta_mac_config(struct phylink_config *config, unsigned int mode,
 
 	if (phylink_test(state->advertising, Pause))
 		new_an |= MVNETA_GMAC_ADVERT_SYM_FLOW_CTRL;
-	if (state->pause & MLO_PAUSE_TXRX_MASK)
-		new_an |= MVNETA_GMAC_CONFIG_FLOW_CTRL;
 
 	if (!phylink_autoneg_inband(mode)) {
-		/* Phy or fixed speed */
-		if (state->duplex)
-			new_an |= MVNETA_GMAC_CONFIG_FULL_DUPLEX;
-
-		if (state->speed == SPEED_1000 || state->speed == SPEED_2500)
-			new_an |= MVNETA_GMAC_CONFIG_GMII_SPEED;
-		else if (state->speed == SPEED_100)
-			new_an |= MVNETA_GMAC_CONFIG_MII_SPEED;
+		/* Phy or fixed speed - nothing to do, leave the
+		 * configured speed, duplex and flow control as-is.
+		 */
 	} else if (state->interface == PHY_INTERFACE_MODE_SGMII) {
 		/* SGMII mode receives the state from the PHY */
 		new_ctrl2 |= MVNETA_GMAC2_INBAND_AN_ENABLE;
 		new_clk |= MVNETA_GMAC_1MS_CLOCK_ENABLE;
 		new_an = (new_an & ~(MVNETA_GMAC_FORCE_LINK_DOWN |
-				     MVNETA_GMAC_FORCE_LINK_PASS)) |
+				     MVNETA_GMAC_FORCE_LINK_PASS |
+				     MVNETA_GMAC_CONFIG_MII_SPEED |
+				     MVNETA_GMAC_CONFIG_GMII_SPEED |
+				     MVNETA_GMAC_CONFIG_FULL_DUPLEX)) |
 			 MVNETA_GMAC_INBAND_AN_ENABLE |
 			 MVNETA_GMAC_AN_SPEED_EN |
 			 MVNETA_GMAC_AN_DUPLEX_EN;
@@ -3813,7 +3805,8 @@ static void mvneta_mac_config(struct phylink_config *config, unsigned int mode,
 		new_ctrl0 |= MVNETA_GMAC0_PORT_1000BASE_X;
 		new_clk |= MVNETA_GMAC_1MS_CLOCK_ENABLE;
 		new_an = (new_an & ~(MVNETA_GMAC_FORCE_LINK_DOWN |
-				     MVNETA_GMAC_FORCE_LINK_PASS)) |
+				     MVNETA_GMAC_FORCE_LINK_PASS |
+				     MVNETA_GMAC_CONFIG_MII_SPEED)) |
 			 MVNETA_GMAC_INBAND_AN_ENABLE |
 			 MVNETA_GMAC_CONFIG_GMII_SPEED |
 			 /* The MAC only supports FD mode */
@@ -3913,8 +3906,36 @@ static void mvneta_mac_link_up(struct phylink_config *config,
 
 	if (!phylink_autoneg_inband(mode)) {
 		val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
-		val &= ~MVNETA_GMAC_FORCE_LINK_DOWN;
+		val &= ~(MVNETA_GMAC_FORCE_LINK_DOWN |
+			 MVNETA_GMAC_CONFIG_MII_SPEED |
+			 MVNETA_GMAC_CONFIG_GMII_SPEED |
+			 MVNETA_GMAC_CONFIG_FLOW_CTRL |
+			 MVNETA_GMAC_CONFIG_FULL_DUPLEX);
 		val |= MVNETA_GMAC_FORCE_LINK_PASS;
+
+		if (speed == SPEED_1000 || speed == SPEED_2500)
+			val |= MVNETA_GMAC_CONFIG_GMII_SPEED;
+		else if (speed == SPEED_100)
+			val |= MVNETA_GMAC_CONFIG_MII_SPEED;
+
+		if (duplex == DUPLEX_FULL)
+			val |= MVNETA_GMAC_CONFIG_FULL_DUPLEX;
+
+		if (tx_pause || rx_pause)
+			val |= MVNETA_GMAC_CONFIG_FLOW_CTRL;
+
+		mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
+	} else {
+		/* When inband doesn't cover flow control or flow control is
+		 * disabled, we need to manually configure it. This bit will
+		 * only have effect if MVNETA_GMAC_AN_FLOW_CTRL_EN is unset.
+		 */
+		val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
+		val &= ~MVNETA_GMAC_CONFIG_FLOW_CTRL;
+
+		if (tx_pause || rx_pause)
+			val |= MVNETA_GMAC_CONFIG_FLOW_CTRL;
+
 		mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
 	}

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Convert the Marvell mvpp2 ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 83 ++++++++++++++-----------
 1 file changed, 47 insertions(+), 36 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index ed8042d97e29..6b9c7ed2547e 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -4976,15 +4976,13 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
 	old_ctrl2 = ctrl2 = readl(port->base + MVPP2_GMAC_CTRL_2_REG);
 	old_ctrl4 = ctrl4 = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
 
-	an &= ~(MVPP2_GMAC_CONFIG_MII_SPEED | MVPP2_GMAC_CONFIG_GMII_SPEED |
-		MVPP2_GMAC_AN_SPEED_EN | MVPP2_GMAC_FC_ADV_EN |
+	an &= ~(MVPP2_GMAC_AN_SPEED_EN | MVPP2_GMAC_FC_ADV_EN |
 		MVPP2_GMAC_FC_ADV_ASM_EN | MVPP2_GMAC_FLOW_CTRL_AUTONEG |
-		MVPP2_GMAC_CONFIG_FULL_DUPLEX | MVPP2_GMAC_AN_DUPLEX_EN |
-		MVPP2_GMAC_IN_BAND_AUTONEG | MVPP2_GMAC_IN_BAND_AUTONEG_BYPASS);
+		MVPP2_GMAC_AN_DUPLEX_EN | MVPP2_GMAC_IN_BAND_AUTONEG |
+		MVPP2_GMAC_IN_BAND_AUTONEG_BYPASS);
 	ctrl0 &= ~MVPP2_GMAC_PORT_TYPE_MASK;
 	ctrl2 &= ~(MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PORT_RESET_MASK |
 		   MVPP2_GMAC_PCS_ENABLE_MASK);
-	ctrl4 &= ~(MVPP22_CTRL4_RX_FC_EN | MVPP22_CTRL4_TX_FC_EN);
 
 	/* Configure port type */
 	if (phy_interface_mode_is_8023z(state->interface)) {
@@ -5014,31 +5012,20 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
 
 	/* Configure negotiation style */
 	if (!phylink_autoneg_inband(mode)) {
-		/* Phy or fixed speed - no in-band AN */
-		if (state->duplex)
-			an |= MVPP2_GMAC_CONFIG_FULL_DUPLEX;
-
-		if (state->speed == SPEED_1000 || state->speed == SPEED_2500)
-			an |= MVPP2_GMAC_CONFIG_GMII_SPEED;
-		else if (state->speed == SPEED_100)
-			an |= MVPP2_GMAC_CONFIG_MII_SPEED;
-
-		if (state->pause & MLO_PAUSE_TX)
-			ctrl4 |= MVPP22_CTRL4_TX_FC_EN;
-		if (state->pause & MLO_PAUSE_RX)
-			ctrl4 |= MVPP22_CTRL4_RX_FC_EN;
+		/* Phy or fixed speed - no in-band AN, nothing to do, leave the
+		 * configured speed, duplex and flow control as-is.
+		 */
 	} else if (state->interface == PHY_INTERFACE_MODE_SGMII) {
 		/* SGMII in-band mode receives the speed and duplex from
 		 * the PHY. Flow control information is not received. */
-		an &= ~(MVPP2_GMAC_FORCE_LINK_DOWN | MVPP2_GMAC_FORCE_LINK_PASS);
+		an &= ~(MVPP2_GMAC_FORCE_LINK_DOWN |
+			MVPP2_GMAC_FORCE_LINK_PASS |
+			MVPP2_GMAC_CONFIG_MII_SPEED |
+			MVPP2_GMAC_CONFIG_GMII_SPEED |
+			MVPP2_GMAC_CONFIG_FULL_DUPLEX);
 		an |= MVPP2_GMAC_IN_BAND_AUTONEG |
 		      MVPP2_GMAC_AN_SPEED_EN |
 		      MVPP2_GMAC_AN_DUPLEX_EN;
-
-		if (state->pause & MLO_PAUSE_TX)
-			ctrl4 |= MVPP22_CTRL4_TX_FC_EN;
-		if (state->pause & MLO_PAUSE_RX)
-			ctrl4 |= MVPP22_CTRL4_RX_FC_EN;
 	} else if (phy_interface_mode_is_8023z(state->interface)) {
 		/* 1000BaseX and 2500BaseX ports cannot negotiate speed nor can
 		 * they negotiate duplex: they are always operating with a fixed
@@ -5046,19 +5033,17 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
 		 * speed and full duplex here.
 		 */
 		ctrl0 |= MVPP2_GMAC_PORT_TYPE_MASK;
-		an &= ~(MVPP2_GMAC_FORCE_LINK_DOWN | MVPP2_GMAC_FORCE_LINK_PASS);
+		an &= ~(MVPP2_GMAC_FORCE_LINK_DOWN |
+			MVPP2_GMAC_FORCE_LINK_PASS |
+			MVPP2_GMAC_CONFIG_MII_SPEED |
+			MVPP2_GMAC_CONFIG_GMII_SPEED |
+			MVPP2_GMAC_CONFIG_FULL_DUPLEX);
 		an |= MVPP2_GMAC_IN_BAND_AUTONEG |
 		      MVPP2_GMAC_CONFIG_GMII_SPEED |
 		      MVPP2_GMAC_CONFIG_FULL_DUPLEX;
 
-		if (state->pause & MLO_PAUSE_AN && state->an_enabled) {
+		if (state->pause & MLO_PAUSE_AN && state->an_enabled)
 			an |= MVPP2_GMAC_FLOW_CTRL_AUTONEG;
-		} else {
-			if (state->pause & MLO_PAUSE_TX)
-				ctrl4 |= MVPP22_CTRL4_TX_FC_EN;
-			if (state->pause & MLO_PAUSE_RX)
-				ctrl4 |= MVPP22_CTRL4_RX_FC_EN;
-		}
 	}
 
 /* Some fields of the auto-negotiation register require the port to be down when
@@ -5155,18 +5140,44 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
 	struct mvpp2_port *port = netdev_priv(dev);
 	u32 val;
 
-	if (!phylink_autoneg_inband(mode)) {
-		if (mvpp2_is_xlg(interface)) {
+	if (mvpp2_is_xlg(interface)) {
+		if (!phylink_autoneg_inband(mode)) {
 			val = readl(port->base + MVPP22_XLG_CTRL0_REG);
 			val &= ~MVPP22_XLG_CTRL0_FORCE_LINK_DOWN;
 			val |= MVPP22_XLG_CTRL0_FORCE_LINK_PASS;
 			writel(val, port->base + MVPP22_XLG_CTRL0_REG);
-		} else {
+		}
+	} else {
+		if (!phylink_autoneg_inband(mode)) {
 			val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
-			val &= ~MVPP2_GMAC_FORCE_LINK_DOWN;
+			val &= ~(MVPP2_GMAC_FORCE_LINK_DOWN |
+				 MVPP2_GMAC_CONFIG_MII_SPEED |
+				 MVPP2_GMAC_CONFIG_GMII_SPEED |
+				 MVPP2_GMAC_CONFIG_FULL_DUPLEX);
 			val |= MVPP2_GMAC_FORCE_LINK_PASS;
+
+			if (speed == SPEED_1000 || speed == SPEED_2500)
+				val |= MVPP2_GMAC_CONFIG_GMII_SPEED;
+			else if (speed == SPEED_100)
+				val |= MVPP2_GMAC_CONFIG_MII_SPEED;
+
+			if (duplex == DUPLEX_FULL)
+				val |= MVPP2_GMAC_CONFIG_FULL_DUPLEX;
+
 			writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
 		}
+
+		/* We can always update the flow control enable bits;
+		 * these will only be effective if flow control AN
+		 * (MVPP2_GMAC_FLOW_CTRL_AUTONEG) is disabled.
+		 */
+		val = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
+		val &= ~(MVPP22_CTRL4_RX_FC_EN | MVPP22_CTRL4_TX_FC_EN);
+		if (tx_pause)
+			val |= MVPP22_CTRL4_TX_FC_EN;
+		if (rx_pause)
+			val |= MVPP22_CTRL4_RX_FC_EN;
+		writel(val, port->base + MVPP22_GMAC_CTRL_4_REG);
 	}
 
 	mvpp2_port_enable(port);

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Using vim to edit the phylink documentation reveals some mistakes due
to the "invisible" pythonesque white space indentation that can't be
seen with other editors. Fix it.

Signed-off-by: Russell King <[email-masked]>
---
 Documentation/networking/sfp-phylink.rst | 32 ++++++++++++++++----------------
 1 file changed, 16 insertions(+), 16 deletions(-)

diff --git a/Documentation/networking/sfp-phylink.rst b/Documentation/networking/sfp-phylink.rst
index 8d7af28cd835..5aec7c8857d0 100644
--- a/Documentation/networking/sfp-phylink.rst
+++ b/Documentation/networking/sfp-phylink.rst
@@ -138,27 +138,27 @@ this documentation.
 
    .. code-block:: c
 
-    static int foo_ethtool_set_link_ksettings(struct net_device *dev,
-					     const struct ethtool_link_ksettings *cmd)
-    {
-	struct foo_priv *priv = netdev_priv(dev);
-
-	return phylink_ethtool_ksettings_set(priv->phylink, cmd);
-    }
-
-    static int foo_ethtool_get_link_ksettings(struct net_device *dev,
-					     struct ethtool_link_ksettings *cmd)
-    {
-	struct foo_priv *priv = netdev_priv(dev);
+	static int foo_ethtool_set_link_ksettings(struct net_device *dev,
+						  const struct ethtool_link_ksettings *cmd)
+	{
+		struct foo_priv *priv = netdev_priv(dev);
+	
+		return phylink_ethtool_ksettings_set(priv->phylink, cmd);
+	}
 
-	return phylink_ethtool_ksettings_get(priv->phylink, cmd);
-    }
+	static int foo_ethtool_get_link_ksettings(struct net_device *dev,
+						  struct ethtool_link_ksettings *cmd)
+	{
+		struct foo_priv *priv = netdev_priv(dev);
+	
+		return phylink_ethtool_ksettings_get(priv->phylink, cmd);
+	}
 
-7. Replace the call to:
+7. Replace the call to::
 
 	phy_dev = of_phy_connect(dev, node, link_func, flags, phy_interface);
 
-   and associated code with a call to:
+   and associated code with a call to::
 
 	err = phylink_of_phy_connect(priv->phylink, node, flags);

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Add support for controlling the MDI-X state of the PHY.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/marvell10g.c | 61 ++++++++++++++++++++++++++++++++++++++++++--
 1 file changed, 59 insertions(+), 2 deletions(-)

diff --git a/drivers/net/phy/marvell10g.c b/drivers/net/phy/marvell10g.c
index 9a4e12a2af07..9d4fed782b19 100644
--- a/drivers/net/phy/marvell10g.c
+++ b/drivers/net/phy/marvell10g.c
@@ -23,6 +23,7 @@
  * link takes priority and the other port is completely locked out.
  */
 #include <linux/ctype.h>
+#include <linux/delay.h>
 #include <linux/hwmon.h>
 #include <linux/marvell_phy.h>
 #include <linux/phy.h>
@@ -39,6 +40,12 @@ enum {
 	MV_PCS_BASE_R		= 0x1000,
 	MV_PCS_1000BASEX	= 0x2000,
 
+	MV_PCS_CSCR1		= 0x8000,
+	MV_PCS_CSCR1_MDIX_MASK	= 0x0060,
+	MV_PCS_CSCR1_MDIX_MDI	= 0x0000,
+	MV_PCS_CSCR1_MDIX_MDIX	= 0x0020,
+	MV_PCS_CSCR1_MDIX_AUTO	= 0x0060,
+
 	MV_PCS_CSSR1		= 0x8008,
 	MV_PCS_CSSR1_SPD1_MASK	= 0xc000,
 	MV_PCS_CSSR1_SPD1_SPD2	= 0xc000,
@@ -216,6 +223,26 @@ static int mv3310_hwmon_probe(struct phy_device *phydev)
 }
 #endif
 
+static int mv3310_reset(struct phy_device *phydev, u32 unit)
+{
+	int retries, val, err;
+
+	err = phy_modify_mmd(phydev, MDIO_MMD_PCS, unit + MDIO_CTRL1,
+			     MDIO_CTRL1_RESET, MDIO_CTRL1_RESET);
+	if (err < 0)
+		return err;
+
+	retries = 20;
+	do {
+		msleep(5);
+		val = phy_read_mmd(phydev, MDIO_MMD_PCS, unit + MDIO_CTRL1);
+		if (val < 0)
+			return val;
+	} while (val & MDIO_CTRL1_RESET && --retries);
+
+	return val & MDIO_CTRL1_RESET ? -ETIMEDOUT : 0;
+}
+
 static int mv3310_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
 {
 	struct phy_device *phydev = upstream;
@@ -316,6 +343,8 @@ static int mv3310_config_init(struct phy_device *phydev)
 	    phydev->interface != PHY_INTERFACE_MODE_10GBASER)
 		return -ENODEV;
 
+	phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
+
 	return 0;
 }
 
@@ -345,14 +374,42 @@ static int mv3310_get_features(struct phy_device *phydev)
 	return 0;
 }
 
+static int mv3310_config_mdix(struct phy_device *phydev)
+{
+	u16 val;
+	int err;
+
+	switch (phydev->mdix_ctrl) {
+	case ETH_TP_MDI_AUTO:
+		val = MV_PCS_CSCR1_MDIX_AUTO;
+		break;
+	case ETH_TP_MDI_X:
+		val = MV_PCS_CSCR1_MDIX_MDIX;
+		break;
+	case ETH_TP_MDI:
+		val = MV_PCS_CSCR1_MDIX_MDI;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	err = phy_modify_mmd_changed(phydev, MDIO_MMD_PCS, MV_PCS_CSCR1,
+				     MV_PCS_CSCR1_MDIX_MASK, val);
+	if (err > 0)
+		err = mv3310_reset(phydev, MV_PCS_BASE_T);
+
+	return err;
+}
+
 static int mv3310_config_aneg(struct phy_device *phydev)
 {
 	bool changed = false;
 	u16 reg;
 	int ret;
 
-	/* We don't support manual MDI control */
-	phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
+	ret = mv3310_config_mdix(phydev);
+	if (ret < 0)
+		return ret;
 
 	if (phydev->autoneg == AUTONEG_DISABLE)
 		return genphy_c45_pma_setup_forced(phydev);

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Add support for the energy detect power down tunable, which saves
around 600mW when the link is down. The 88x3310 supports off, rx-only
and NLP every second. Enable EDPD by default for 88x3310.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/marvell10g.c | 86 +++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 85 insertions(+), 1 deletion(-)

diff --git a/drivers/net/phy/marvell10g.c b/drivers/net/phy/marvell10g.c
index 9d4fed782b19..7092feb9e6b5 100644
--- a/drivers/net/phy/marvell10g.c
+++ b/drivers/net/phy/marvell10g.c
@@ -41,6 +41,10 @@ enum {
 	MV_PCS_1000BASEX	= 0x2000,
 
 	MV_PCS_CSCR1		= 0x8000,
+	MV_PCS_CSCR1_ED_MASK	= 0x0300,
+	MV_PCS_CSCR1_ED_OFF	= 0x0000,
+	MV_PCS_CSCR1_ED_RX	= 0x0200,
+	MV_PCS_CSCR1_ED_NLP	= 0x0300,
 	MV_PCS_CSCR1_MDIX_MASK	= 0x0060,
 	MV_PCS_CSCR1_MDIX_MDI	= 0x0000,
 	MV_PCS_CSCR1_MDIX_MDIX	= 0x0020,
@@ -243,6 +247,59 @@ static int mv3310_reset(struct phy_device *phydev, u32 unit)
 	return val & MDIO_CTRL1_RESET ? -ETIMEDOUT : 0;
 }
 
+static int mv3310_get_edpd(struct phy_device *phydev, u16 *edpd)
+{
+	int val;
+
+	val = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_PCS_CSCR1);
+	if (val < 0)
+		return val;
+
+	switch (val & MV_PCS_CSCR1_ED_MASK) {
+	case MV_PCS_CSCR1_ED_NLP:
+		*edpd = 1000;
+		break;
+	case MV_PCS_CSCR1_ED_RX:
+		*edpd = ETHTOOL_PHY_EDPD_NO_TX;
+		break;
+	default:
+		*edpd = ETHTOOL_PHY_EDPD_DISABLE;
+		break;
+	}
+	return 0;
+}
+
+static int mv3310_set_edpd(struct phy_device *phydev, u16 edpd)
+{
+	u16 val;
+	int err;
+
+	switch (edpd) {
+	case 1000:
+	case ETHTOOL_PHY_EDPD_DFLT_TX_MSECS:
+		val = MV_PCS_CSCR1_ED_NLP;
+		break;
+
+	case ETHTOOL_PHY_EDPD_NO_TX:
+		val = MV_PCS_CSCR1_ED_RX;
+		break;
+
+	case ETHTOOL_PHY_EDPD_DISABLE:
+		val = MV_PCS_CSCR1_ED_OFF;
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	err = phy_modify_mmd_changed(phydev, MDIO_MMD_PCS, MV_PCS_CSCR1,
+				     MV_PCS_CSCR1_ED_MASK, val);
+	if (err > 0)
+		err = mv3310_reset(phydev, MV_PCS_BASE_T);
+
+	return err;
+}
+
 static int mv3310_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
 {
 	struct phy_device *phydev = upstream;
@@ -345,7 +402,8 @@ static int mv3310_config_init(struct phy_device *phydev)
 
 	phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
 
-	return 0;
+	/* Enable EDPD mode - saving 600mW */
+	return mv3310_set_edpd(phydev, ETHTOOL_PHY_EDPD_DFLT_TX_MSECS);
 }
 
 static int mv3310_get_features(struct phy_device *phydev)
@@ -594,6 +652,28 @@ static int mv3310_read_status(struct phy_device *phydev)
 	return 0;
 }
 
+static int mv3310_get_tunable(struct phy_device *phydev,
+			      struct ethtool_tunable *tuna, void *data)
+{
+	switch (tuna->id) {
+	case ETHTOOL_PHY_EDPD:
+		return mv3310_get_edpd(phydev, data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static int mv3310_set_tunable(struct phy_device *phydev,
+			      struct ethtool_tunable *tuna, const void *data)
+{
+	switch (tuna->id) {
+	case ETHTOOL_PHY_EDPD:
+		return mv3310_set_edpd(phydev, *(u16 *)data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
 static struct phy_driver mv3310_drivers[] = {
 	{
 		.phy_id		= MARVELL_PHY_ID_88X3310,
@@ -608,6 +688,8 @@ static struct phy_driver mv3310_drivers[] = {
 		.config_aneg	= mv3310_config_aneg,
 		.aneg_done	= mv3310_aneg_done,
 		.read_status	= mv3310_read_status,
+		.get_tunable	= mv3310_get_tunable,
+		.set_tunable	= mv3310_set_tunable,
 	},
 	{
 		.phy_id		= MARVELL_PHY_ID_88E2110,
@@ -621,6 +703,8 @@ static struct phy_driver mv3310_drivers[] = {
 		.config_aneg	= mv3310_config_aneg,
 		.aneg_done	= mv3310_aneg_done,
 		.read_status	= mv3310_read_status,
+		.get_tunable	= mv3310_get_tunable,
+		.set_tunable	= mv3310_set_tunable,
 	},
 };

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Place the 88x3310 into powersaving mode when probing, which saves 600mW
per PHY. For both PHYs on the Macchiatobin double-shot, this saves
about 10% of the board idle power.

Reviewed-by: Andrew Lunn <[email-masked]>
Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/marvell10g.c | 30 ++++++++++++++++++++++++++----
 1 file changed, 26 insertions(+), 4 deletions(-)

diff --git a/drivers/net/phy/marvell10g.c b/drivers/net/phy/marvell10g.c
index 7092feb9e6b5..7e05b92504f0 100644
--- a/drivers/net/phy/marvell10g.c
+++ b/drivers/net/phy/marvell10g.c
@@ -227,6 +227,18 @@ static int mv3310_hwmon_probe(struct phy_device *phydev)
 }
 #endif
 
+static int mv3310_power_down(struct phy_device *phydev)
+{
+	return phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL,
+				MV_V2_PORT_CTRL_PWRDOWN);
+}
+
+static int mv3310_power_up(struct phy_device *phydev)
+{
+	return phy_clear_bits_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL,
+				  MV_V2_PORT_CTRL_PWRDOWN);
+}
+
 static int mv3310_reset(struct phy_device *phydev, u32 unit)
 {
 	int retries, val, err;
@@ -348,6 +360,11 @@ static int mv3310_probe(struct phy_device *phydev)
 
 	dev_set_drvdata(&phydev->mdio.dev, priv);
 
+	/* Powering down the port when not in use saves about 600mW */
+	ret = mv3310_power_down(phydev);
+	if (ret)
+		return ret;
+
 	ret = mv3310_hwmon_probe(phydev);
 	if (ret)
 		return ret;
@@ -357,16 +374,14 @@ static int mv3310_probe(struct phy_device *phydev)
 
 static int mv3310_suspend(struct phy_device *phydev)
 {
-	return phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL,
-				MV_V2_PORT_CTRL_PWRDOWN);
+	return mv3310_power_down(phydev);
 }
 
 static int mv3310_resume(struct phy_device *phydev)
 {
 	int ret;
 
-	ret = phy_clear_bits_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL,
-				 MV_V2_PORT_CTRL_PWRDOWN);
+	ret = mv3310_power_up(phydev);
 	if (ret)
 		return ret;
 
@@ -392,6 +407,8 @@ static bool mv3310_has_pma_ngbaset_quirk(struct phy_device *phydev)
 
 static int mv3310_config_init(struct phy_device *phydev)
 {
+	int err;
+
 	/* Check that the PHY interface type is compatible */
 	if (phydev->interface != PHY_INTERFACE_MODE_SGMII &&
 	    phydev->interface != PHY_INTERFACE_MODE_2500BASEX &&
@@ -402,6 +419,11 @@ static int mv3310_config_init(struct phy_device *phydev)

+	/* Power up so reset works */
+	err = mv3310_power_up(phydev);
+	if (err)
+		return err;
+
 	/* Enable EDPD mode - saving 600mW */
 	return mv3310_set_edpd(phydev, ETHTOOL_PHY_EDPD_DFLT_TX_MSECS);
 }

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

From: Vladimir Oltean <[email-masked]>

The switches supported so far by the driver only have non-SerDes ports,
so they should be configured in the PHYLINK callback that provides the
resolved PHY link parameters.

Signed-off-by: Vladimir Oltean <[email-masked]>
Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/dsa/sja1105/sja1105_main.c | 13 +++++++++----
 1 file changed, 9 insertions(+), 4 deletions(-)

diff --git a/drivers/net/dsa/sja1105/sja1105_main.c b/drivers/net/dsa/sja1105/sja1105_main.c
index a3709f7ad0e2..65925f5f6b84 100644
--- a/drivers/net/dsa/sja1105/sja1105_main.c
+++ b/drivers/net/dsa/sja1105/sja1105_main.c
@@ -765,15 +765,16 @@ static void sja1105_mac_config(struct dsa_switch *ds, int port,
 {
 	struct sja1105_private *priv = ds->priv;
 
-	if (sja1105_phy_mode_mismatch(priv, port, state->interface))
+	if (sja1105_phy_mode_mismatch(priv, port, state->interface)) {
+		dev_err(ds->dev, "Changing PHY mode to %s not supported!\n",
+			phy_modes(state->interface));
 		return;
+	}
 
 	if (link_an_mode == MLO_AN_INBAND) {
 		dev_err(ds->dev, "In-band AN not supported!\n");
 		return;
 	}
-
-	sja1105_adjust_port_config(priv, port, state->speed);
 }
 
 static void sja1105_mac_link_down(struct dsa_switch *ds, int port,
@@ -790,7 +791,11 @@ static void sja1105_mac_link_up(struct dsa_switch *ds, int port,
 				int speed, int duplex,
 				bool tx_pause, bool rx_pause)
 {
-	sja1105_inhibit_tx(ds->priv, BIT(port), false);
+	struct sja1105_private *priv = ds->priv;
+
+	sja1105_adjust_port_config(priv, port, speed);
+
+	sja1105_inhibit_tx(priv, BIT(port), false);
 }
 
 static void sja1105_phylink_validate(struct dsa_switch *ds, int port,

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

From: Jose Abreu <[email-masked]>

Add a define for XLGMII interface.

Signed-off-by: Jose Abreu <[email-masked]>
Signed-off-by: David S. Miller <[email-masked]>
---
 include/linux/phy.h | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/include/linux/phy.h b/include/linux/phy.h
index 118de9f5bbb2..ac956ea1a87c 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -94,6 +94,7 @@ typedef enum {
 	PHY_INTERFACE_MODE_RTBI,
 	PHY_INTERFACE_MODE_SMII,
 	PHY_INTERFACE_MODE_XGMII,
+	PHY_INTERFACE_MODE_XLGMII,
 	PHY_INTERFACE_MODE_MOCA,
 	PHY_INTERFACE_MODE_QSGMII,
 	PHY_INTERFACE_MODE_TRGMII,
@@ -165,6 +166,8 @@ static inline const char *phy_modes(phy_interface_t interface)
 		return "smii";
 	case PHY_INTERFACE_MODE_XGMII:
 		return "xgmii";
+	case PHY_INTERFACE_MODE_XLGMII:
+		return "xlgmii";
 	case PHY_INTERFACE_MODE_MOCA:
 		return "moca";
 	case PHY_INTERFACE_MODE_QSGMII:

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Add XLGMII interface and the list of XLGMII speeds to PHYLINK.

Signed-off-by: Jose Abreu <[email-masked]>
Signed-off-by: David S. Miller <[email-masked]>
---
 drivers/net/phy/phylink.c | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 5347275215be..bf5b5026eff4 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -324,6 +324,33 @@ static int phylink_parse_mode(struct phylink *pl, struct fwnode_handle *fwnode)
 			phylink_set(pl->supported, 10000baseER_Full);
 			break;
 
+		case PHY_INTERFACE_MODE_XLGMII:
+			phylink_set(pl->supported, 25000baseCR_Full);
+			phylink_set(pl->supported, 25000baseKR_Full);
+			phylink_set(pl->supported, 25000baseSR_Full);
+			phylink_set(pl->supported, 40000baseKR4_Full);
+			phylink_set(pl->supported, 40000baseCR4_Full);
+			phylink_set(pl->supported, 40000baseSR4_Full);
+			phylink_set(pl->supported, 40000baseLR4_Full);
+			phylink_set(pl->supported, 50000baseCR2_Full);
+			phylink_set(pl->supported, 50000baseKR2_Full);
+			phylink_set(pl->supported, 50000baseSR2_Full);
+			phylink_set(pl->supported, 50000baseKR_Full);
+			phylink_set(pl->supported, 50000baseSR_Full);
+			phylink_set(pl->supported, 50000baseCR_Full);
+			phylink_set(pl->supported, 50000baseLR_ER_FR_Full);
+			phylink_set(pl->supported, 50000baseDR_Full);
+			phylink_set(pl->supported, 100000baseKR4_Full);
+			phylink_set(pl->supported, 100000baseSR4_Full);
+			phylink_set(pl->supported, 100000baseCR4_Full);
+			phylink_set(pl->supported, 100000baseLR4_ER4_Full);
+			phylink_set(pl->supported, 100000baseKR2_Full);
+			phylink_set(pl->supported, 100000baseSR2_Full);
+			phylink_set(pl->supported, 100000baseCR2_Full);
+			phylink_set(pl->supported, 100000baseLR2_ER2_FR2_Full);
+			phylink_set(pl->supported, 100000baseDR2_Full);
+			break;
+
 		default:
 			phylink_err(pl,
 				    "incorrect link mode %s for in-band status\n",

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Add a LPA to linkmode decoder for 1000BASE-X protocols; this decoder
only provides the modify semantics similar to other such decoders.
This replaces the unused mii_lpa_to_ethtool_lpa_x() helper.

Signed-off-by: Russell King <[email-masked]>
---
 include/linux/mii.h | 37 +++++++++++++++++++------------------
 1 file changed, 19 insertions(+), 18 deletions(-)

diff --git a/include/linux/mii.h b/include/linux/mii.h
index 18c6208f56fc..309de4a3e6e7 100644
--- a/include/linux/mii.h
+++ b/include/linux/mii.h
@@ -354,24 +354,6 @@ static inline u32 mii_adv_to_ethtool_adv_x(u32 adv)
 	return result;
 }
 
-/**
- * mii_lpa_to_ethtool_lpa_x
- * @adv: value of the MII_LPA register
- *
- * A small helper function that translates MII_LPA
- * bits, when in 1000Base-X mode, to ethtool
- * LP advertisement settings.
- */
-static inline u32 mii_lpa_to_ethtool_lpa_x(u32 lpa)
-{
-	u32 result = 0;
-
-	if (lpa & LPA_LPACK)
-		result |= ADVERTISED_Autoneg;
-
-	return result | mii_adv_to_ethtool_adv_x(lpa);
-}
-
 /**
  * mii_lpa_mod_linkmode_adv_sgmii
  * @lp_advertising: pointer to destination link mode.
@@ -535,6 +517,25 @@ static inline u32 linkmode_adv_to_lcl_adv_t(unsigned long *advertising)
 	return lcl_adv;
 }
 
+/**
+ * mii_lpa_mod_linkmode_x - decode the link partner's config_reg to linkmodes
+ * @linkmodes: link modes array
+ * @lpa: config_reg word from link partner
+ * @fd_bit: link mode for 1000XFULL bit
+ */
+static inline void mii_lpa_mod_linkmode_x(unsigned long *linkmodes, u16 lpa,
+					 int fd_bit)
+{
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, linkmodes,
+			 lpa & LPA_LPACK);
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_Pause_BIT, linkmodes,
+			 lpa & LPA_1000XPAUSE);
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, linkmodes,
+			 lpa & LPA_1000XPAUSE_ASYM);
+	linkmode_mod_bit(fd_bit, linkmodes,
+			 lpa & LPA_1000XFULL);
+}
+
 /**
  * mii_advertise_flowctrl - get flow control advertisement flags
  * @cap: Flow control capabilities (FLOW_CTRL_RX, FLOW_CTRL_TX or both)

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Add a helper to convert a linkmode advertisement to a clause 37
advertisement value for 1000base-x and 2500base-x.

Signed-off-by: Russell King <[email-masked]>
---
 include/linux/mii.h | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/include/linux/mii.h b/include/linux/mii.h
index 309de4a3e6e7..219b93cad1dd 100644
--- a/include/linux/mii.h
+++ b/include/linux/mii.h
@@ -536,6 +536,26 @@ static inline void mii_lpa_mod_linkmode_x(unsigned long *linkmodes, u16 lpa,
 			 lpa & LPA_1000XFULL);
 }
 
+/**
+ * linkmode_adv_to_mii_adv_x - encode a linkmode to config_reg
+ * @linkmodes: linkmodes
+ * @fd_bit: full duplex bit
+ */
+static inline u16 linkmode_adv_to_mii_adv_x(const unsigned long *linkmodes,
+					    int fd_bit)
+{
+	u16 adv = 0;
+
+	if (linkmode_test_bit(fd_bit, linkmodes))
+		adv |= ADVERTISE_1000XFULL;
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_Pause_BIT, linkmodes))
+		adv |= ADVERTISE_1000XPAUSE;
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, linkmodes))
+		adv |= ADVERTISE_1000XPSE_ASYM;
+
+	return adv;
+}
+
 /**
  * mii_advertise_flowctrl - get flow control advertisement flags
  * @cap: Flow control capabilities (FLOW_CTRL_RX, FLOW_CTRL_TX or both)

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Issue a warning to the kernel log if phylink_mac_link_state() returns
an error. This should not occur, but let's make it visible.

Signed-off-by: Russell King <[email-masked]>
---
 net/dsa/port.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/net/dsa/port.c b/net/dsa/port.c
index e6875d8f944d..a18e65a474a5 100644
--- a/net/dsa/port.c
+++ b/net/dsa/port.c
@@ -457,6 +457,7 @@ static void dsa_port_phylink_mac_pcs_get_state(struct phylink_config *config,
 {
 	struct dsa_port *dp = container_of(config, struct dsa_port, pl_config);
 	struct dsa_switch *ds = dp->ds;
+	int err;
 
 	/* Only called for inband modes */
 	if (!ds->ops->phylink_mac_link_state) {
@@ -464,8 +465,12 @@ static void dsa_port_phylink_mac_pcs_get_state(struct phylink_config *config,
 		return;
 	}
 
-	if (ds->ops->phylink_mac_link_state(ds, dp->index, state) < 0)
+	err = ds->ops->phylink_mac_link_state(ds, dp->index, state);
+	if (err < 0) {
+		dev_err(ds->dev, "p%d: phylink_mac_link_state() failed: %d\n",
+			dp->index, err);
 		state->link = 0;
+	}
 }
 
 static void dsa_port_phylink_mac_config(struct phylink_config *config,

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

The SGMII/1000base-X serdes register set is a clause 22 register set
offset at 0x2000 in the PHYXS device. Rather than inventing our own
defintions, use those that already exist, and name the register
MV88E6390_SGMII_BMCR.  Also remove the unused MV88E6390_SGMII_STATUS
definitions.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/dsa/mv88e6xxx/serdes.c | 10 ++++------
 drivers/net/dsa/mv88e6xxx/serdes.h |  9 +--------
 2 files changed, 5 insertions(+), 14 deletions(-)

diff --git a/drivers/net/dsa/mv88e6xxx/serdes.c b/drivers/net/dsa/mv88e6xxx/serdes.c
index 8d8b3b74aee1..05129b3c7a62 100644
--- a/drivers/net/dsa/mv88e6xxx/serdes.c
+++ b/drivers/net/dsa/mv88e6xxx/serdes.c
@@ -387,20 +387,18 @@ static int mv88e6390_serdes_power_sgmii(struct mv88e6xxx_chip *chip, u8 lane,
 	int err;
 
 	err = mv88e6390_serdes_read(chip, lane, MDIO_MMD_PHYXS,
-				    MV88E6390_SGMII_CONTROL, &val);
+				    MV88E6390_SGMII_BMCR, &val);
 	if (err)
 		return err;
 
 	if (up)
-		new_val = val & ~(MV88E6390_SGMII_CONTROL_RESET |
-				  MV88E6390_SGMII_CONTROL_LOOPBACK |
-				  MV88E6390_SGMII_CONTROL_PDOWN);
+		new_val = val & ~(BMCR_RESET | BMCR_LOOPBACK | BMCR_PDOWN);
 	else
-		new_val = val | MV88E6390_SGMII_CONTROL_PDOWN;
+		new_val = val | BMCR_PDOWN;
 
 	if (val != new_val)
 		err = mv88e6390_serdes_write(chip, lane, MDIO_MMD_PHYXS,
-					     MV88E6390_SGMII_CONTROL, new_val);
+					     MV88E6390_SGMII_BMCR, new_val);
 
 	return err;
 }
diff --git a/drivers/net/dsa/mv88e6xxx/serdes.h b/drivers/net/dsa/mv88e6xxx/serdes.h
index d16ef4da20b0..890c7d4ef707 100644
--- a/drivers/net/dsa/mv88e6xxx/serdes.h
+++ b/drivers/net/dsa/mv88e6xxx/serdes.h
@@ -47,14 +47,7 @@
 #define MV88E6390_PCS_CONTROL_1_PDOWN		BIT(11)
 
 /* 1000BASE-X and SGMII */
-#define MV88E6390_SGMII_CONTROL		0x2000
-#define MV88E6390_SGMII_CONTROL_RESET		BIT(15)
-#define MV88E6390_SGMII_CONTROL_LOOPBACK	BIT(14)
-#define MV88E6390_SGMII_CONTROL_PDOWN		BIT(11)
-#define MV88E6390_SGMII_STATUS		0x2001
-#define MV88E6390_SGMII_STATUS_AN_DONE		BIT(5)
-#define MV88E6390_SGMII_STATUS_REMOTE_FAULT	BIT(4)
-#define MV88E6390_SGMII_STATUS_LINK		BIT(2)
+#define MV88E6390_SGMII_BMCR		(0x2000 + MII_BMCR)
 #define MV88E6390_SGMII_INT_ENABLE	0xa001
 #define MV88E6390_SGMII_INT_SPEED_CHANGE	BIT(14)
 #define MV88E6390_SGMII_INT_DUPLEX_CHANGE	BIT(13)

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Only configure the interface settings in mac_config(), leaving the
speed and duplex settings to mac_link_up to deal with.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/dsa/mv88e6xxx/chip.c | 67 +++++++++++++++++++++-------------------
 1 file changed, 35 insertions(+), 32 deletions(-)

diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
index cbf67e92efb2..d87f97cf4b9e 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.c
+++ b/drivers/net/dsa/mv88e6xxx/chip.c
@@ -397,6 +397,28 @@ static void mv88e6xxx_irq_poll_free(struct mv88e6xxx_chip *chip)
 	mv88e6xxx_reg_unlock(chip);
 }
 
+static int mv88e6xxx_port_config_interface(struct mv88e6xxx_chip *chip,
+					   int port, phy_interface_t interface)
+{
+	int err;
+
+	if (chip->info->ops->port_set_rgmii_delay) {
+		err = chip->info->ops->port_set_rgmii_delay(chip, port,
+							    interface);
+		if (err && err != -EOPNOTSUPP)
+			return err;
+	}
+
+	if (chip->info->ops->port_set_cmode) {
+		err = chip->info->ops->port_set_cmode(chip, port,
+						      interface);
+		if (err && err != -EOPNOTSUPP)
+			return err;
+	}
+
+	return 0;
+}
+
 int mv88e6xxx_port_setup_mac(struct mv88e6xxx_chip *chip, int port, int link,
 			     int speed, int duplex, int pause,
 			     phy_interface_t mode)
@@ -451,19 +473,7 @@ int mv88e6xxx_port_setup_mac(struct mv88e6xxx_chip *chip, int port, int link,
 			goto restore_link;
 	}
 
-	if (chip->info->ops->port_set_rgmii_delay) {
-		err = chip->info->ops->port_set_rgmii_delay(chip, port, mode);
-		if (err && err != -EOPNOTSUPP)
-			goto restore_link;
-	}
-
-	if (chip->info->ops->port_set_cmode) {
-		err = chip->info->ops->port_set_cmode(chip, port, mode);
-		if (err && err != -EOPNOTSUPP)
-			goto restore_link;
-	}
-
-	err = 0;
+	err = mv88e6xxx_port_config_interface(chip, port, mode);
 restore_link:
 	if (chip->info->ops->port_set_link(chip, port, link))
 		dev_err(chip->dev, "p%d: failed to restore MAC's link\n", port);
@@ -603,33 +613,26 @@ static void mv88e6xxx_mac_config(struct dsa_switch *ds, int port,
 				 const struct phylink_link_state *state)
 {
 	struct mv88e6xxx_chip *chip = ds->priv;
-	int speed, duplex, link, pause, err;
+	int err;
 
+	/* FIXME: is this the correct test? If we're in fixed mode on an
+	 * internal port, why should we process this any different from
+	 * PHY mode? On the other hand, the port may be automedia between
+	 * an internal PHY and the serdes...
+	 */
 	if ((mode == MLO_AN_PHY) && mv88e6xxx_phy_is_internal(ds, port))
 		return;
 
-	if (mode == MLO_AN_FIXED) {
-		link = LINK_FORCED_UP;
-		speed = state->speed;
-		duplex = state->duplex;
-	} else if (!mv88e6xxx_phy_is_internal(ds, port)) {
-		link = state->link;
-		speed = state->speed;
-		duplex = state->duplex;
-	} else {
-		speed = SPEED_UNFORCED;
-		duplex = DUPLEX_UNFORCED;
-		link = LINK_UNFORCED;
-	}
-	pause = !!phylink_test(state->advertising, Pause);
-
 	mv88e6xxx_reg_lock(chip);
-	err = mv88e6xxx_port_setup_mac(chip, port, link, speed, duplex, pause,
-				       state->interface);
+	/* FIXME: should we force the link down here - but if we do, how
+	 * do we restore the link force/unforce state? The driver layering
+	 * gets in the way.
+	 */
+	err = mv88e6xxx_port_config_interface(chip, port, state->interface);
 	mv88e6xxx_reg_unlock(chip);
 
 	if (err && err != -EOPNOTSUPP)
-		dev_err(ds->dev, "p%d: failed to configure MAC\n", port);
+		dev_err(ds->dev, "p%d: failed to configure MAC/PCS\n", port);
 }
 
 static void mv88e6xxx_mac_link_down(struct dsa_switch *ds, int port,

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Extend the mv88e6xxx phylink implementation down to Serdes PHYs, which
handle the PCS layer of such links.

- Implement phylink PCS link state reading, so that we can provide
  ethtool with the linkmodes and link speed in the expected manner.
  Note: this will only be called for in-band negotiation, which is
  only supported by the serdes interfaces.
- Implement phylink PCS configuration, so that the in-band AN and
  advertisement can be configured.
- Implement phylink PCS negotiation restart, so that the in-band AN
  can be restarted.
- Implement phylink PCS link up, so that when operating out-of-band,
  the Serdes can be configured for the appropriate fixed speed mode.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/dsa/mv88e6xxx/chip.c   | 174 ++++++++++++++++---
 drivers/net/dsa/mv88e6xxx/chip.h   |  14 +-
 drivers/net/dsa/mv88e6xxx/serdes.c | 342 +++++++++++++++++++++++++++++++------
 drivers/net/dsa/mv88e6xxx/serdes.h |  24 +++
 4 files changed, 480 insertions(+), 74 deletions(-)

diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
index d87f97cf4b9e..e1a8af509d5a 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.c
+++ b/drivers/net/dsa/mv88e6xxx/chip.c
@@ -419,9 +419,9 @@ static int mv88e6xxx_port_config_interface(struct mv88e6xxx_chip *chip,
 	return 0;
 }
 
-int mv88e6xxx_port_setup_mac(struct mv88e6xxx_chip *chip, int port, int link,
-			     int speed, int duplex, int pause,
-			     phy_interface_t mode)
+static int mv88e6xxx_port_setup_mac(struct mv88e6xxx_chip *chip, int port,
+				    int link, int speed, int duplex, int pause,
+				    phy_interface_t mode)
 {
 	struct phylink_link_state state;
 	int err;
@@ -488,6 +488,81 @@ static int mv88e6xxx_phy_is_internal(struct dsa_switch *ds, int port)
 	return port < chip->info->num_internal_phys;
 }
 
+static int mv88e6xxx_serdes_pcs_get_state(struct dsa_switch *ds, int port,
+					  struct phylink_link_state *state)
+{
+	struct mv88e6xxx_chip *chip = ds->priv;
+	u8 lane;
+	int err;
+
+	mv88e6xxx_reg_lock(chip);
+	lane = mv88e6xxx_serdes_get_lane(chip, port);
+	if (lane && chip->info->ops->serdes_pcs_get_state)
+		err = chip->info->ops->serdes_pcs_get_state(chip, port, lane,
+							    state);
+	else
+		err = -EOPNOTSUPP;
+	mv88e6xxx_reg_unlock(chip);
+
+	return err;
+}
+
+static int mv88e6xxx_serdes_pcs_config(struct mv88e6xxx_chip *chip, int port,
+				       unsigned int mode,
+				       phy_interface_t interface,
+				       const unsigned long *advertise)
+{
+	const struct mv88e6xxx_ops *ops = chip->info->ops;
+	u8 lane;
+
+	if (ops->serdes_pcs_config) {
+		lane = mv88e6xxx_serdes_get_lane(chip, port);
+		if (lane)
+			return ops->serdes_pcs_config(chip, port, lane, mode,
+						      interface, advertise);
+	}
+
+	return 0;
+}
+
+static void mv88e6xxx_serdes_pcs_an_restart(struct dsa_switch *ds, int port)
+{
+	struct mv88e6xxx_chip *chip = ds->priv;
+	const struct mv88e6xxx_ops *ops;
+	int err = 0;
+	u8 lane;
+
+	ops = chip->info->ops;
+
+	if (ops->serdes_pcs_an_restart) {
+		mv88e6xxx_reg_lock(chip);
+		lane = mv88e6xxx_serdes_get_lane(chip, port);
+		if (lane)
+			err = ops->serdes_pcs_an_restart(chip, port, lane);
+		mv88e6xxx_reg_unlock(chip);
+
+		if (err)
+			dev_err(ds->dev, "p%d: failed to restart AN\n", port);
+	}
+}
+
+static int mv88e6xxx_serdes_pcs_link_up(struct mv88e6xxx_chip *chip, int port,
+					unsigned int mode,
+					int speed, int duplex)
+{
+	const struct mv88e6xxx_ops *ops = chip->info->ops;
+	u8 lane;
+
+	if (!phylink_autoneg_inband(mode) && ops->serdes_pcs_link_up) {
+		lane = mv88e6xxx_serdes_get_lane(chip, port);
+		if (lane)
+			return ops->serdes_pcs_link_up(chip, port, lane,
+						       speed, duplex);
+	}
+
+	return 0;
+}
+
 static void mv88e6065_phylink_validate(struct mv88e6xxx_chip *chip, int port,
 				       unsigned long *mask,
 				       struct phylink_link_state *state)
@@ -592,22 +667,6 @@ static void mv88e6xxx_validate(struct dsa_switch *ds, int port,
 	phylink_helper_basex_speed(state);
 }
 
-static int mv88e6xxx_link_state(struct dsa_switch *ds, int port,
-				struct phylink_link_state *state)
-{
-	struct mv88e6xxx_chip *chip = ds->priv;
-	int err;
-
-	mv88e6xxx_reg_lock(chip);
-	if (chip->info->ops->port_link_state)
-		err = chip->info->ops->port_link_state(chip, port, state);
-	else
-		err = -EOPNOTSUPP;
-	mv88e6xxx_reg_unlock(chip);
-
-	return err;
-}
-
 static void mv88e6xxx_mac_config(struct dsa_switch *ds, int port,
 				 unsigned int mode,
 				 const struct phylink_link_state *state)
@@ -629,6 +688,18 @@ static void mv88e6xxx_mac_config(struct dsa_switch *ds, int port,
 	 * gets in the way.
 	 */
 	err = mv88e6xxx_port_config_interface(chip, port, state->interface);
+	if (err && err != -EOPNOTSUPP)
+		goto err_unlock;
+
+	err = mv88e6xxx_serdes_pcs_config(chip, port, mode, state->interface,
+					  state->advertising);
+	/* FIXME: we should restart negotiation if something changed - which
+	 * is something we get if we convert to using phylinks PCS operations.
+	 */
+	if (err > 0)
+		err = 0;
+
+err_unlock:
 	mv88e6xxx_reg_unlock(chip);
 
 	if (err && err != -EOPNOTSUPP)
@@ -683,9 +754,14 @@ static void mv88e6xxx_mac_link_up(struct dsa_switch *ds, int port,
 		/* FIXME: for an automedia port, should we force the link
 		 * down here - what if the link comes up due to "other" media
 		 * while we're bringing the port up, how is the exclusivity
-		 * handled in the Marvell hardware? E.g. port 4 on 88E6532
+		 * handled in the Marvell hardware? E.g. port 2 on 88E6390
 		 * shared between internal PHY and Serdes.
 		 */
+		err = mv88e6xxx_serdes_pcs_link_up(chip, port, mode, speed,
+						   duplex);
+		if (err)
+			goto error;
+
 		if (ops->port_set_speed) {
 			err = ops->port_set_speed(chip, port, speed);
 			if (err && err != -EOPNOTSUPP)
@@ -3547,6 +3623,11 @@ static const struct mv88e6xxx_ops mv88e6141_ops = {
 	.vtu_loadpurge = mv88e6352_g1_vtu_loadpurge,
 	.serdes_power = mv88e6390_serdes_power,
 	.serdes_get_lane = mv88e6341_serdes_get_lane,
+	/* Check status register pause & lpa register */
+	.serdes_pcs_get_state = mv88e6390_serdes_pcs_get_state,
+	.serdes_pcs_config = mv88e6390_serdes_pcs_config,
+	.serdes_pcs_an_restart = mv88e6390_serdes_pcs_an_restart,
+	.serdes_pcs_link_up = mv88e6390_serdes_pcs_link_up,
 	.serdes_irq_mapping = mv88e6390_serdes_irq_mapping,
 	.serdes_irq_enable = mv88e6390_serdes_irq_enable,
 	.serdes_irq_status = mv88e6390_serdes_irq_status,
@@ -3719,6 +3800,10 @@ static const struct mv88e6xxx_ops mv88e6172_ops = {
 	.vtu_getnext = mv88e6352_g1_vtu_getnext,
 	.vtu_loadpurge = mv88e6352_g1_vtu_loadpurge,
 	.serdes_get_lane = mv88e6352_serdes_get_lane,
+	.serdes_pcs_get_state = mv88e6352_serdes_pcs_get_state,
+	.serdes_pcs_config = mv88e6352_serdes_pcs_config,
+	.serdes_pcs_an_restart = mv88e6352_serdes_pcs_an_restart,
+	.serdes_pcs_link_up = mv88e6352_serdes_pcs_link_up,
 	.serdes_power = mv88e6352_serdes_power,
 	.gpio_ops = &mv88e6352_gpio_ops,
 	.phylink_validate = mv88e6352_phylink_validate,
@@ -3810,6 +3895,10 @@ static const struct mv88e6xxx_ops mv88e6176_ops = {
 	.vtu_getnext = mv88e6352_g1_vtu_getnext,
 	.vtu_loadpurge = mv88e6352_g1_vtu_loadpurge,
 	.serdes_get_lane = mv88e6352_serdes_get_lane,
+	.serdes_pcs_get_state = mv88e6352_serdes_pcs_get_state,
+	.serdes_pcs_config = mv88e6352_serdes_pcs_config,
+	.serdes_pcs_an_restart = mv88e6352_serdes_pcs_an_restart,
+	.serdes_pcs_link_up = mv88e6352_serdes_pcs_link_up,
 	.serdes_power = mv88e6352_serdes_power,
 	.serdes_irq_mapping = mv88e6352_serdes_irq_mapping,
 	.serdes_irq_enable = mv88e6352_serdes_irq_enable,
@@ -3898,6 +3987,11 @@ static const struct mv88e6xxx_ops mv88e6190_ops = {
 	.vtu_loadpurge = mv88e6390_g1_vtu_loadpurge,
 	.serdes_power = mv88e6390_serdes_power,
 	.serdes_get_lane = mv88e6390_serdes_get_lane,
+	/* Check status register pause & lpa register */
+	.serdes_pcs_get_state = mv88e6390_serdes_pcs_get_state,
+	.serdes_pcs_config = mv88e6390_serdes_pcs_config,
+	.serdes_pcs_an_restart = mv88e6390_serdes_pcs_an_restart,
+	.serdes_pcs_link_up = mv88e6390_serdes_pcs_link_up,
 	.serdes_irq_mapping = mv88e6390_serdes_irq_mapping,
 	.serdes_irq_enable = mv88e6390_serdes_irq_enable,
 	.serdes_irq_status = mv88e6390_serdes_irq_status,
@@ -3952,6 +4046,11 @@ static const struct mv88e6xxx_ops mv88e6190x_ops = {
 	.vtu_loadpurge = mv88e6390_g1_vtu_loadpurge,
 	.serdes_power = mv88e6390_serdes_power,
 	.serdes_get_lane = mv88e6390x_serdes_get_lane,
+	/* Check status register pause & lpa register */
+	.serdes_pcs_get_state = mv88e6390_serdes_pcs_get_state,
+	.serdes_pcs_config = mv88e6390_serdes_pcs_config,
+	.serdes_pcs_an_restart = mv88e6390_serdes_pcs_an_restart,
+	.serdes_pcs_link_up = mv88e6390_serdes_pcs_link_up,
 	.serdes_irq_mapping = mv88e6390_serdes_irq_mapping,
 	.serdes_irq_enable = mv88e6390_serdes_irq_enable,
 	.serdes_irq_status = mv88e6390_serdes_irq_status,
@@ -4005,6 +4104,11 @@ static const struct mv88e6xxx_ops mv88e6191_ops = {
 	.vtu_loadpurge = mv88e6390_g1_vtu_loadpurge,
 	.serdes_power = mv88e6390_serdes_power,
 	.serdes_get_lane = mv88e6390_serdes_get_lane,
+	/* Check status register pause & lpa register */
+	.serdes_pcs_get_state = mv88e6390_serdes_pcs_get_state,
+	.serdes_pcs_config = mv88e6390_serdes_pcs_config,
+	.serdes_pcs_an_restart = mv88e6390_serdes_pcs_an_restart,
+	.serdes_pcs_link_up = mv88e6390_serdes_pcs_link_up,
 	.serdes_irq_mapping = mv88e6390_serdes_irq_mapping,
 	.serdes_irq_enable = mv88e6390_serdes_irq_enable,
 	.serdes_irq_status = mv88e6390_serdes_irq_status,
@@ -4060,6 +4164,10 @@ static const struct mv88e6xxx_ops mv88e6240_ops = {
 	.vtu_getnext = mv88e6352_g1_vtu_getnext,
 	.vtu_loadpurge = mv88e6352_g1_vtu_loadpurge,
 	.serdes_get_lane = mv88e6352_serdes_get_lane,
+	.serdes_pcs_get_state = mv88e6352_serdes_pcs_get_state,
+	.serdes_pcs_config = mv88e6352_serdes_pcs_config,
+	.serdes_pcs_an_restart = mv88e6352_serdes_pcs_an_restart,
+	.serdes_pcs_link_up = mv88e6352_serdes_pcs_link_up,
 	.serdes_power = mv88e6352_serdes_power,
 	.serdes_irq_mapping = mv88e6352_serdes_irq_mapping,
 	.serdes_irq_enable = mv88e6352_serdes_irq_enable,
@@ -4154,6 +4262,11 @@ static const struct mv88e6xxx_ops mv88e6290_ops = {
 	.vtu_loadpurge = mv88e6390_g1_vtu_loadpurge,
 	.serdes_power = mv88e6390_serdes_power,
 	.serdes_get_lane = mv88e6390_serdes_get_lane,
+	/* Check status register pause & lpa register */
+	.serdes_pcs_get_state = mv88e6390_serdes_pcs_get_state,
+	.serdes_pcs_config = mv88e6390_serdes_pcs_config,
+	.serdes_pcs_an_restart = mv88e6390_serdes_pcs_an_restart,
+	.serdes_pcs_link_up = mv88e6390_serdes_pcs_link_up,
 	.serdes_irq_mapping = mv88e6390_serdes_irq_mapping,
 	.serdes_irq_enable = mv88e6390_serdes_irq_enable,
 	.serdes_irq_status = mv88e6390_serdes_irq_status,
@@ -4295,6 +4408,11 @@ static const struct mv88e6xxx_ops mv88e6341_ops = {
 	.vtu_loadpurge = mv88e6352_g1_vtu_loadpurge,
 	.serdes_power = mv88e6390_serdes_power,
 	.serdes_get_lane = mv88e6341_serdes_get_lane,
+	/* Check status register pause & lpa register */
+	.serdes_pcs_get_state = mv88e6390_serdes_pcs_get_state,
+	.serdes_pcs_config = mv88e6390_serdes_pcs_config,
+	.serdes_pcs_an_restart = mv88e6390_serdes_pcs_an_restart,
+	.serdes_pcs_link_up = mv88e6390_serdes_pcs_link_up,
 	.serdes_irq_mapping = mv88e6390_serdes_irq_mapping,
 	.serdes_irq_enable = mv88e6390_serdes_irq_enable,
 	.serdes_irq_status = mv88e6390_serdes_irq_status,
@@ -4434,6 +4552,10 @@ static const struct mv88e6xxx_ops mv88e6352_ops = {
 	.vtu_getnext = mv88e6352_g1_vtu_getnext,
 	.vtu_loadpurge = mv88e6352_g1_vtu_loadpurge,
 	.serdes_get_lane = mv88e6352_serdes_get_lane,
+	.serdes_pcs_get_state = mv88e6352_serdes_pcs_get_state,
+	.serdes_pcs_config = mv88e6352_serdes_pcs_config,
+	.serdes_pcs_an_restart = mv88e6352_serdes_pcs_an_restart,
+	.serdes_pcs_link_up = mv88e6352_serdes_pcs_link_up,
 	.serdes_power = mv88e6352_serdes_power,
 	.serdes_irq_mapping = mv88e6352_serdes_irq_mapping,
 	.serdes_irq_enable = mv88e6352_serdes_irq_enable,
@@ -4493,6 +4615,11 @@ static const struct mv88e6xxx_ops mv88e6390_ops = {
 	.vtu_loadpurge = mv88e6390_g1_vtu_loadpurge,
 	.serdes_power = mv88e6390_serdes_power,
 	.serdes_get_lane = mv88e6390_serdes_get_lane,
+	/* Check status register pause & lpa register */
+	.serdes_pcs_get_state = mv88e6390_serdes_pcs_get_state,
+	.serdes_pcs_config = mv88e6390_serdes_pcs_config,
+	.serdes_pcs_an_restart = mv88e6390_serdes_pcs_an_restart,
+	.serdes_pcs_link_up = mv88e6390_serdes_pcs_link_up,
 	.serdes_irq_mapping = mv88e6390_serdes_irq_mapping,
 	.serdes_irq_enable = mv88e6390_serdes_irq_enable,
 	.serdes_irq_status = mv88e6390_serdes_irq_status,
@@ -4551,6 +4678,10 @@ static const struct mv88e6xxx_ops mv88e6390x_ops = {
 	.vtu_loadpurge = mv88e6390_g1_vtu_loadpurge,
 	.serdes_power = mv88e6390_serdes_power,
 	.serdes_get_lane = mv88e6390x_serdes_get_lane,
+	.serdes_pcs_get_state = mv88e6390_serdes_pcs_get_state,
+	.serdes_pcs_config = mv88e6390_serdes_pcs_config,
+	.serdes_pcs_an_restart = mv88e6390_serdes_pcs_an_restart,
+	.serdes_pcs_link_up = mv88e6390_serdes_pcs_link_up,
 	.serdes_irq_mapping = mv88e6390_serdes_irq_mapping,
 	.serdes_irq_enable = mv88e6390_serdes_irq_enable,
 	.serdes_irq_status = mv88e6390_serdes_irq_status,
@@ -5427,8 +5558,9 @@ static const struct dsa_switch_ops mv88e6xxx_switch_ops = {
 	.setup			= mv88e6xxx_setup,
 	.teardown		= mv88e6xxx_teardown,
 	.phylink_validate	= mv88e6xxx_validate,
-	.phylink_mac_link_state	= mv88e6xxx_link_state,
+	.phylink_mac_link_state	= mv88e6xxx_serdes_pcs_get_state,
 	.phylink_mac_config	= mv88e6xxx_mac_config,
+	.phylink_mac_an_restart	= mv88e6xxx_serdes_pcs_an_restart,
 	.phylink_mac_link_down	= mv88e6xxx_mac_link_down,
 	.phylink_mac_link_up	= mv88e6xxx_mac_link_up,
 	.get_strings		= mv88e6xxx_get_strings,
diff --git a/drivers/net/dsa/mv88e6xxx/chip.h b/drivers/net/dsa/mv88e6xxx/chip.h
index 79cad5e751c6..38dc336970db 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.h
+++ b/drivers/net/dsa/mv88e6xxx/chip.h
@@ -502,6 +502,17 @@ struct mv88e6xxx_ops {
 	/* SERDES lane mapping */
 	u8 (*serdes_get_lane)(struct mv88e6xxx_chip *chip, int port);
 
+	int (*serdes_pcs_get_state)(struct mv88e6xxx_chip *chip, int port,
+				    u8 lane, struct phylink_link_state *state);
+	int (*serdes_pcs_config)(struct mv88e6xxx_chip *chip, int port,
+				 u8 lane, unsigned int mode,
+				 phy_interface_t interface,
+				 const unsigned long *advertise);
+	int (*serdes_pcs_an_restart)(struct mv88e6xxx_chip *chip, int port,
+				     u8 lane);
+	int (*serdes_pcs_link_up)(struct mv88e6xxx_chip *chip, int port,
+				  u8 lane, int speed, int duplex);
+
 	/* SERDES interrupt handling */
 	unsigned int (*serdes_irq_mapping)(struct mv88e6xxx_chip *chip,
 					   int port);
@@ -664,9 +675,6 @@ int mv88e6xxx_wait_mask(struct mv88e6xxx_chip *chip, int addr, int reg,
 			u16 mask, u16 val);
 int mv88e6xxx_wait_bit(struct mv88e6xxx_chip *chip, int addr, int reg,
 		       int bit, int val);
-int mv88e6xxx_port_setup_mac(struct mv88e6xxx_chip *chip, int port, int link,
-			     int speed, int duplex, int pause,
-			     phy_interface_t mode);
 struct mii_bus *mv88e6xxx_default_mdio_bus(struct mv88e6xxx_chip *chip);
 
 static inline void mv88e6xxx_reg_lock(struct mv88e6xxx_chip *chip)
diff --git a/drivers/net/dsa/mv88e6xxx/serdes.c b/drivers/net/dsa/mv88e6xxx/serdes.c
index 05129b3c7a62..dba42aecfd5f 100644
--- a/drivers/net/dsa/mv88e6xxx/serdes.c
+++ b/drivers/net/dsa/mv88e6xxx/serdes.c
@@ -49,6 +49,52 @@ static int mv88e6390_serdes_write(struct mv88e6xxx_chip *chip,
 	return mv88e6xxx_phy_write(chip, lane, reg_c45, val);
 }
 
+static int mv88e6xxx_serdes_pcs_get_state(struct mv88e6xxx_chip *chip,
+					  u16 status, u16 lpa,
+					  struct phylink_link_state *state)
+{
+	if (status & MV88E6390_SGMII_PHY_STATUS_SPD_DPL_VALID) {
+		state->link = !!(status & MV88E6390_SGMII_PHY_STATUS_LINK);
+		state->duplex = status &
+				MV88E6390_SGMII_PHY_STATUS_DUPLEX_FULL ?
+			                         DUPLEX_FULL : DUPLEX_HALF;
+
+		if (status & MV88E6390_SGMII_PHY_STATUS_TX_PAUSE)
+			state->pause |= MLO_PAUSE_TX;
+		if (status & MV88E6390_SGMII_PHY_STATUS_RX_PAUSE)
+			state->pause |= MLO_PAUSE_RX;
+
+		switch (status & MV88E6390_SGMII_PHY_STATUS_SPEED_MASK) {
+		case MV88E6390_SGMII_PHY_STATUS_SPEED_1000:
+			if (state->interface == PHY_INTERFACE_MODE_2500BASEX)
+				state->speed = SPEED_2500;
+			else
+				state->speed = SPEED_1000;
+			break;
+		case MV88E6390_SGMII_PHY_STATUS_SPEED_100:
+			state->speed = SPEED_100;
+			break;
+		case MV88E6390_SGMII_PHY_STATUS_SPEED_10:
+			state->speed = SPEED_10;
+			break;
+		default:
+			dev_err(chip->dev, "invalid PHY speed\n");
+			return -EINVAL;
+		}
+	} else {
+		state->link = false;
+	}
+
+	if (state->interface == PHY_INTERFACE_MODE_2500BASEX)
+		mii_lpa_mod_linkmode_x(state->lp_advertising, lpa,
+				       ETHTOOL_LINK_MODE_2500baseX_Full_BIT);
+	else if (state->interface == PHY_INTERFACE_MODE_1000BASEX)
+		mii_lpa_mod_linkmode_x(state->lp_advertising, lpa,
+				       ETHTOOL_LINK_MODE_1000baseX_Full_BIT);
+
+	return 0;
+}
+
 int mv88e6352_serdes_power(struct mv88e6xxx_chip *chip, int port, u8 lane,
 			   bool up)
 {
@@ -70,6 +116,120 @@ int mv88e6352_serdes_power(struct mv88e6xxx_chip *chip, int port, u8 lane,
 	return err;
 }
 
+int mv88e6352_serdes_pcs_config(struct mv88e6xxx_chip *chip, int port,
+				u8 lane, unsigned int mode,
+				phy_interface_t interface,
+				const unsigned long *advertise)
+{
+	u16 adv, bmcr, val;
+	bool changed;
+	int err;
+
+	switch (interface) {
+	case PHY_INTERFACE_MODE_SGMII:
+		adv = 0x0001;
+		break;
+
+	case PHY_INTERFACE_MODE_1000BASEX:
+		adv = linkmode_adv_to_mii_adv_x(advertise,
+					ETHTOOL_LINK_MODE_1000baseX_Full_BIT);
+		break;
+
+	default:
+		return 0;
+	}
+
+	err = mv88e6352_serdes_read(chip, MII_ADVERTISE, &val);
+	if (err)
+		return err;
+
+	changed = val != adv;
+	if (changed) {
+		err = mv88e6352_serdes_write(chip, MII_ADVERTISE, adv);
+		if (err)
+			return err;
+	}
+
+	err = mv88e6352_serdes_read(chip, MII_BMCR, &val);
+	if (err)
+		return err;
+
+	if (phylink_autoneg_inband(mode))
+		bmcr = val | BMCR_ANENABLE;
+	else
+		bmcr = val & ~BMCR_ANENABLE;
+
+	if (bmcr == val)
+		return changed;
+
+	return mv88e6352_serdes_write(chip, MII_BMCR, bmcr);
+}
+
+int mv88e6352_serdes_pcs_get_state(struct mv88e6xxx_chip *chip, int port,
+				   u8 lane, struct phylink_link_state *state)
+{
+	u16 lpa, status;
+	int err;
+
+	err = mv88e6352_serdes_read(chip, 0x11, &status);
+	if (err) {
+		dev_err(chip->dev, "can't read Serdes PHY status: %d\n", err);
+		return err;
+	}
+
+	err = mv88e6352_serdes_read(chip, MII_LPA, &lpa);
+	if (err) {
+		dev_err(chip->dev, "can't read Serdes PHY LPA: %d\n", err);
+		return err;
+	}
+
+	return mv88e6xxx_serdes_pcs_get_state(chip, status, lpa, state);
+}
+
+int mv88e6352_serdes_pcs_an_restart(struct mv88e6xxx_chip *chip, int port,
+				    u8 lane)
+{
+	u16 bmcr;
+	int err;
+
+	err = mv88e6352_serdes_read(chip, MII_BMCR, &bmcr);
+	if (err)
+		return err;
+
+	return mv88e6352_serdes_write(chip, MII_BMCR, bmcr | BMCR_ANRESTART);
+}
+
+int mv88e6352_serdes_pcs_link_up(struct mv88e6xxx_chip *chip, int port,
+				 u8 lane, int speed, int duplex)
+{
+	u16 val, bmcr;
+	int err;
+
+	err = mv88e6352_serdes_read(chip, MII_BMCR, &val);
+	if (err)
+		return err;
+
+	bmcr = val & ~(BMCR_SPEED100 | BMCR_FULLDPLX | BMCR_SPEED1000);
+	switch (speed) {
+	case SPEED_1000:
+		bmcr |= BMCR_SPEED1000;
+		break;
+	case SPEED_100:
+		bmcr |= BMCR_SPEED100;
+		break;
+	case SPEED_10:
+		break;
+	}
+
+	if (duplex == DUPLEX_FULL)
+		bmcr |= BMCR_FULLDPLX;
+
+	if (bmcr == val)
+		return 0;
+
+	return mv88e6352_serdes_write(chip, MII_BMCR, bmcr);
+}
+
 u8 mv88e6352_serdes_get_lane(struct mv88e6xxx_chip *chip, int port)
 {
 	u8 cmode = chip->ports[port].cmode;
@@ -515,71 +675,153 @@ int mv88e6390_serdes_power(struct mv88e6xxx_chip *chip, int port, u8 lane,
 	return err;
 }
 
-static void mv88e6390_serdes_irq_link_sgmii(struct mv88e6xxx_chip *chip,
-					    int port, u8 lane)
+int mv88e6390_serdes_pcs_config(struct mv88e6xxx_chip *chip, int port,
+				u8 lane, unsigned int mode,
+				phy_interface_t interface,
+				const unsigned long *advertise)
 {
-	u8 cmode = chip->ports[port].cmode;
-	struct dsa_switch *ds = chip->ds;
-	int duplex = DUPLEX_UNKNOWN;
-	int speed = SPEED_UNKNOWN;
-	phy_interface_t mode;
-	int link, err;
-	u16 status;
+	u16 val, bmcr, adv;
+	bool changed;
+	int err;
+
+	switch (interface) {
+	case PHY_INTERFACE_MODE_SGMII:
+		adv = 0x0001;
+		break;
+
+	case PHY_INTERFACE_MODE_1000BASEX:
+		adv = linkmode_adv_to_mii_adv_x(advertise,
+					ETHTOOL_LINK_MODE_1000baseX_Full_BIT);
+		break;
+
+	case PHY_INTERFACE_MODE_2500BASEX:
+		adv = linkmode_adv_to_mii_adv_x(advertise,
+					ETHTOOL_LINK_MODE_2500baseX_Full_BIT);
+		break;
+
+	default:
+		return 0;
+	}
+
+	err = mv88e6390_serdes_read(chip, lane, MDIO_MMD_PHYXS,
+				    MV88E6390_SGMII_ADVERTISE, &val);
+	if (err)
+		return err;
+
+	changed = val != adv;
+	if (changed) {
+		err = mv88e6390_serdes_write(chip, lane, MDIO_MMD_PHYXS,
+					     MV88E6390_SGMII_ADVERTISE, adv);
+		if (err)
+			return err;
+	}
+
+	err = mv88e6390_serdes_read(chip, lane, MDIO_MMD_PHYXS,
+				    MV88E6390_SGMII_BMCR, &val);
+	if (err)
+		return err;
+
+	if (phylink_autoneg_inband(mode))
+		bmcr = val | BMCR_ANENABLE;
+	else
+		bmcr = val & ~BMCR_ANENABLE;
+
+	/* setting ANENABLE triggers a restart of negotiation */
+	if (bmcr == val)
+		return changed;
+
+	return mv88e6390_serdes_write(chip, lane, MDIO_MMD_PHYXS,
+				      MV88E6390_SGMII_BMCR, bmcr);
+}
+
+int mv88e6390_serdes_pcs_get_state(struct mv88e6xxx_chip *chip, int port,
+				   u8 lane, struct phylink_link_state *state)
+{
+	u16 lpa, status;
+	int err;
 
 	err = mv88e6390_serdes_read(chip, lane, MDIO_MMD_PHYXS,
 				    MV88E6390_SGMII_PHY_STATUS, &status);
 	if (err) {
-		dev_err(chip->dev, "can't read SGMII PHY status: %d\n", err);
-		return;
+		dev_err(chip->dev, "can't read Serdes PHY status: %d\n", err);
+		return err;
 	}
 
-	link = status & MV88E6390_SGMII_PHY_STATUS_LINK ?
-	       LINK_FORCED_UP : LINK_FORCED_DOWN;
+	err = mv88e6390_serdes_read(chip, lane, MDIO_MMD_PHYXS,
+				    MV88E6390_SGMII_LPA, &lpa);
+	if (err) {
+		dev_err(chip->dev, "can't read Serdes PHY LPA: %d\n", err);
+		return err;
+	}
 
-	if (status & MV88E6390_SGMII_PHY_STATUS_SPD_DPL_VALID) {
-		duplex = status & MV88E6390_SGMII_PHY_STATUS_DUPLEX_FULL ?
-			 DUPLEX_FULL : DUPLEX_HALF;
+	return mv88e6xxx_serdes_pcs_get_state(chip, status, lpa, state);
+}
 
-		switch (status & MV88E6390_SGMII_PHY_STATUS_SPEED_MASK) {
-		case MV88E6390_SGMII_PHY_STATUS_SPEED_1000:
-			if (cmode == MV88E6XXX_PORT_STS_CMODE_2500BASEX)
-				speed = SPEED_2500;
-			else
-				speed = SPEED_1000;
-			break;
-		case MV88E6390_SGMII_PHY_STATUS_SPEED_100:
-			speed = SPEED_100;
-			break;
-		case MV88E6390_SGMII_PHY_STATUS_SPEED_10:
-			speed = SPEED_10;
-			break;
-		default:
-			dev_err(chip->dev, "invalid PHY speed\n");
-			return;
-		}
-	}
+int mv88e6390_serdes_pcs_an_restart(struct mv88e6xxx_chip *chip, int port,
+				    u8 lane)
+{
+	u16 bmcr;
+	int err;
 
-	switch (cmode) {
-	case MV88E6XXX_PORT_STS_CMODE_SGMII:
-		mode = PHY_INTERFACE_MODE_SGMII;
+	err = mv88e6390_serdes_read(chip, lane, MDIO_MMD_PHYXS,
+				    MV88E6390_SGMII_BMCR, &bmcr);
+	if (err)
+		return err;
+
+	return mv88e6390_serdes_write(chip, lane, MDIO_MMD_PHYXS,
+				      MV88E6390_SGMII_BMCR,
+				      bmcr | BMCR_ANRESTART);
+}
+
+int mv88e6390_serdes_pcs_link_up(struct mv88e6xxx_chip *chip, int port,
+				 u8 lane, int speed, int duplex)
+{
+	u16 val, bmcr;
+	int err;
+
+	err = mv88e6390_serdes_read(chip, lane, MDIO_MMD_PHYXS,
+				    MV88E6390_SGMII_BMCR, &val);
+	if (err)
+		return err;
+
+	bmcr = val & ~(BMCR_SPEED100 | BMCR_FULLDPLX | BMCR_SPEED1000);
+	switch (speed) {
+	case SPEED_2500:
+	case SPEED_1000:
+		bmcr |= BMCR_SPEED1000;
 		break;
-	case MV88E6XXX_PORT_STS_CMODE_1000BASEX:
-		mode = PHY_INTERFACE_MODE_1000BASEX;
+	case SPEED_100:
+		bmcr |= BMCR_SPEED100;
 		break;
-	case MV88E6XXX_PORT_STS_CMODE_2500BASEX:
-		mode = PHY_INTERFACE_MODE_2500BASEX;
+	case SPEED_10:
 		break;
-	default:
-		mode = PHY_INTERFACE_MODE_NA;
 	}
 
-	err = mv88e6xxx_port_setup_mac(chip, port, link, speed, duplex,
-				       PAUSE_OFF, mode);
-	if (err)
-		dev_err(chip->dev, "can't propagate PHY settings to MAC: %d\n",
-			err);
-	else
-		dsa_port_phylink_mac_change(ds, port, link == LINK_FORCED_UP);
+	if (duplex == DUPLEX_FULL)
+		bmcr |= BMCR_FULLDPLX;
+
+	if (bmcr == val)
+		return 0;
+
+	return mv88e6390_serdes_write(chip, lane, MDIO_MMD_PHYXS,
+				      MV88E6390_SGMII_BMCR, bmcr);
+}
+
+static void mv88e6390_serdes_irq_link_sgmii(struct mv88e6xxx_chip *chip,
+					    int port, u8 lane)
+{
+	u16 status;
+	int err;
+
+	err = mv88e6390_serdes_read(chip, lane, MDIO_MMD_PHYXS,
+				    MV88E6390_SGMII_PHY_STATUS, &status);
+	if (err) {
+		dev_err(chip->dev, "can't read SGMII PHY status: %d\n", err);
+		return;
+	}
+
+	dsa_port_phylink_mac_change(chip->ds, port,
+				!!(status & MV88E6390_SGMII_PHY_STATUS_LINK));
 }
 
 static int mv88e6390_serdes_irq_enable_sgmii(struct mv88e6xxx_chip *chip,
diff --git a/drivers/net/dsa/mv88e6xxx/serdes.h b/drivers/net/dsa/mv88e6xxx/serdes.h
index 890c7d4ef707..e52a8f81beba 100644
--- a/drivers/net/dsa/mv88e6xxx/serdes.h
+++ b/drivers/net/dsa/mv88e6xxx/serdes.h
@@ -48,6 +48,8 @@
 
 /* 1000BASE-X and SGMII */
 #define MV88E6390_SGMII_BMCR		(0x2000 + MII_BMCR)
+#define MV88E6390_SGMII_ADVERTISE	(0x2000 + MII_ADVERTISE)
+#define MV88E6390_SGMII_LPA		(0x2000 + MII_LPA)
 #define MV88E6390_SGMII_INT_ENABLE	0xa001
 #define MV88E6390_SGMII_INT_SPEED_CHANGE	BIT(14)
 #define MV88E6390_SGMII_INT_DUPLEX_CHANGE	BIT(13)
@@ -66,6 +68,8 @@
 #define MV88E6390_SGMII_PHY_STATUS_DUPLEX_FULL	BIT(13)
 #define MV88E6390_SGMII_PHY_STATUS_SPD_DPL_VALID BIT(11)
 #define MV88E6390_SGMII_PHY_STATUS_LINK		BIT(10)
+#define MV88E6390_SGMII_PHY_STATUS_TX_PAUSE	BIT(3)
+#define MV88E6390_SGMII_PHY_STATUS_RX_PAUSE	BIT(2)
 
 /* Packet generator pad packet checker */
 #define MV88E6390_PG_CONTROL		0xf010
@@ -75,6 +79,26 @@ u8 mv88e6341_serdes_get_lane(struct mv88e6xxx_chip *chip, int port);
 u8 mv88e6352_serdes_get_lane(struct mv88e6xxx_chip *chip, int port);
 u8 mv88e6390_serdes_get_lane(struct mv88e6xxx_chip *chip, int port);
 u8 mv88e6390x_serdes_get_lane(struct mv88e6xxx_chip *chip, int port);
+int mv88e6352_serdes_pcs_config(struct mv88e6xxx_chip *chip, int port,
+				u8 lane, unsigned int mode,
+				phy_interface_t interface,
+				const unsigned long *advertise);
+int mv88e6390_serdes_pcs_config(struct mv88e6xxx_chip *chip, int port,
+				u8 lane, unsigned int mode,
+				phy_interface_t interface,
+				const unsigned long *advertise);
+int mv88e6352_serdes_pcs_get_state(struct mv88e6xxx_chip *chip, int port,
+				   u8 lane, struct phylink_link_state *state);
+int mv88e6390_serdes_pcs_get_state(struct mv88e6xxx_chip *chip, int port,
+				   u8 lane, struct phylink_link_state *state);
+int mv88e6352_serdes_pcs_an_restart(struct mv88e6xxx_chip *chip, int port,
+				    u8 lane);
+int mv88e6390_serdes_pcs_an_restart(struct mv88e6xxx_chip *chip, int port,
+				    u8 lane);
+int mv88e6352_serdes_pcs_link_up(struct mv88e6xxx_chip *chip, int port,
+				 u8 lane, int speed, int duplex);
+int mv88e6390_serdes_pcs_link_up(struct mv88e6xxx_chip *chip, int port,
+				 u8 lane, int speed, int duplex);
 unsigned int mv88e6352_serdes_irq_mapping(struct mv88e6xxx_chip *chip,
 					  int port);
 unsigned int mv88e6390_serdes_irq_mapping(struct mv88e6xxx_chip *chip,

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

phylink_mac_change() is supposed to be called with a 'false' argument
if the link has gone down since it was last reported up; this is to
ensure that link events along with renegotiation events are always
correctly reported to userspace.

Read the BMSR once when we have an interrupt, and report the link
latched status to phylink via phylink_mac_change().  phylink will deal
automatically with re-reading the link state once it has processed the
link-down event.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/dsa/mv88e6xxx/serdes.c | 33 ++++++++++++---------------------
 drivers/net/dsa/mv88e6xxx/serdes.h |  1 +
 2 files changed, 13 insertions(+), 21 deletions(-)

diff --git a/drivers/net/dsa/mv88e6xxx/serdes.c b/drivers/net/dsa/mv88e6xxx/serdes.c
index dba42aecfd5f..ad9629945f91 100644
--- a/drivers/net/dsa/mv88e6xxx/serdes.c
+++ b/drivers/net/dsa/mv88e6xxx/serdes.c
@@ -340,26 +340,17 @@ int mv88e6352_serdes_get_stats(struct mv88e6xxx_chip *chip, int port,
 
 static void mv88e6352_serdes_irq_link(struct mv88e6xxx_chip *chip, int port)
 {
-	struct dsa_switch *ds = chip->ds;
-	u16 status;
-	bool up;
+	u16 bmsr;
 	int err;
 
-	err = mv88e6352_serdes_read(chip, MII_BMSR, &status);
-	if (err)
-		return;
-
-	/* Status must be read twice in order to give the current link
-	 * status. Otherwise the change in link status since the last
-	 * read of the register is returned.
-	 */
-	err = mv88e6352_serdes_read(chip, MII_BMSR, &status);
-	if (err)
+	/* If the link has dropped, we want to know about it. */
+	err = mv88e6352_serdes_read(chip, MII_BMSR, &bmsr);
+	if (err) {
+		dev_err(chip->dev, "can't read Serdes BMSR: %d\n", err);
 		return;
+	}
 
-	up = status & BMSR_LSTATUS;
-
-	dsa_port_phylink_mac_change(ds, port, up);
+	dsa_port_phylink_mac_change(chip->ds, port, !!(bmsr & BMSR_LSTATUS));
 }
 
 irqreturn_t mv88e6352_serdes_irq_status(struct mv88e6xxx_chip *chip, int port,
@@ -810,18 +801,18 @@ int mv88e6390_serdes_pcs_link_up(struct mv88e6xxx_chip *chip, int port,
 static void mv88e6390_serdes_irq_link_sgmii(struct mv88e6xxx_chip *chip,
 					    int port, u8 lane)
 {
-	u16 status;
+	u16 bmsr;
 	int err;
 
+	/* If the link has dropped, we want to know about it. */
 	err = mv88e6390_serdes_read(chip, lane, MDIO_MMD_PHYXS,
-				    MV88E6390_SGMII_PHY_STATUS, &status);
+				    MV88E6390_SGMII_BMSR, &bmsr);
 	if (err) {
-		dev_err(chip->dev, "can't read SGMII PHY status: %d\n", err);
+		dev_err(chip->dev, "can't read Serdes BMSR: %d\n", err);
 		return;
 	}
 
-	dsa_port_phylink_mac_change(chip->ds, port,
-				!!(status & MV88E6390_SGMII_PHY_STATUS_LINK));
+	dsa_port_phylink_mac_change(chip->ds, port, !!(bmsr & BMSR_LSTATUS));
 }
 
index e52a8f81beba..3365864818cf 100644
@@ -48,6 +48,7 @@
 
 /* 1000BASE-X and SGMII */
 #define MV88E6390_SGMII_BMCR		(0x2000 + MII_BMCR)
+#define MV88E6390_SGMII_BMSR		(0x2000 + MII_BMSR)
 #define MV88E6390_SGMII_ADVERTISE	(0x2000 + MII_ADVERTISE)
 #define MV88E6390_SGMII_LPA		(0x2000 + MII_LPA)
 #define MV88E6390_SGMII_INT_ENABLE	0xa001

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Setting the speed independently of duplex makes little sense; the two
parameters result from negotiation or fixed setup, and may have inter-
dependencies. Moreover, they are always controlled via the same
register - having them split means we have to read-modify-write this
register twice.

Combine the two operations into a single port_set_speed_duplex()
operation. Not only is this more efficient, it reduces the size of the
code as well.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/dsa/mv88e6xxx/chip.c | 103 ++++++++++++-------------------------
 drivers/net/dsa/mv88e6xxx/chip.h |  18 +++----
 drivers/net/dsa/mv88e6xxx/port.c | 108 +++++++++++++++++++--------------------
 drivers/net/dsa/mv88e6xxx/port.h |  23 +++++----
 4 files changed, 107 insertions(+), 145 deletions(-)

diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
index e1a8af509d5a..2bc686f12f2a 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.c
+++ b/drivers/net/dsa/mv88e6xxx/chip.c
@@ -452,8 +452,9 @@ static int mv88e6xxx_port_setup_mac(struct mv88e6xxx_chip *chip, int port,
 	if (err)
 		return err;
 
-	if (chip->info->ops->port_set_speed) {
-		err = chip->info->ops->port_set_speed(chip, port, speed);
+	if (chip->info->ops->port_set_speed_duplex) {
+		err = chip->info->ops->port_set_speed_duplex(chip, port,
+							     speed, duplex);
 		if (err && err != -EOPNOTSUPP)
 			goto restore_link;
 	}
@@ -467,12 +468,6 @@ static int mv88e6xxx_port_setup_mac(struct mv88e6xxx_chip *chip, int port,
 			goto restore_link;
 	}
 
-	if (chip->info->ops->port_set_duplex) {
-		err = chip->info->ops->port_set_duplex(chip, port, duplex);
-		if (err && err != -EOPNOTSUPP)
-			goto restore_link;
-	}
-
 	err = mv88e6xxx_port_config_interface(chip, port, mode);
 restore_link:
 	if (chip->info->ops->port_set_link(chip, port, link))
@@ -762,14 +757,9 @@ static void mv88e6xxx_mac_link_up(struct dsa_switch *ds, int port,
 		if (err)
 			goto error;
 
-		if (ops->port_set_speed) {
-			err = ops->port_set_speed(chip, port, speed);
-			if (err && err != -EOPNOTSUPP)
-				goto error;
-		}
-
-		if (ops->port_set_duplex) {
-			err = ops->port_set_duplex(chip, port, duplex);
+		if (ops->port_set_speed_duplex) {
+			err = ops->port_set_speed_duplex(chip, port,
+							 speed, duplex);
 			if (err && err != -EOPNOTSUPP)
 				goto error;
 		}
@@ -3402,8 +3392,7 @@ static const struct mv88e6xxx_ops mv88e6085_ops = {
 	.phy_read = mv88e6185_phy_ppu_read,
 	.phy_write = mv88e6185_phy_ppu_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
-	.port_set_speed = mv88e6185_port_set_speed,
+	.port_set_speed_duplex = mv88e6185_port_set_speed_duplex,
 	.port_tag_remap = mv88e6095_port_tag_remap,
 	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
 	.port_set_egress_floods = mv88e6352_port_set_egress_floods,
@@ -3442,8 +3431,7 @@ static const struct mv88e6xxx_ops mv88e6095_ops = {
 	.phy_read = mv88e6185_phy_ppu_read,
 	.phy_write = mv88e6185_phy_ppu_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
-	.port_set_speed = mv88e6185_port_set_speed,
+	.port_set_speed_duplex = mv88e6185_port_set_speed_duplex,
 	.port_set_frame_mode = mv88e6085_port_set_frame_mode,
 	.port_set_egress_floods = mv88e6185_port_set_egress_floods,
 	.port_set_upstream_port = mv88e6095_port_set_upstream_port,
@@ -3473,8 +3461,7 @@ static const struct mv88e6xxx_ops mv88e6097_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
-	.port_set_speed = mv88e6185_port_set_speed,
+	.port_set_speed_duplex = mv88e6185_port_set_speed_duplex,
 	.port_tag_remap = mv88e6095_port_tag_remap,
 	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
 	.port_set_egress_floods = mv88e6352_port_set_egress_floods,
@@ -3513,8 +3500,7 @@ static const struct mv88e6xxx_ops mv88e6123_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
-	.port_set_speed = mv88e6185_port_set_speed,
+	.port_set_speed_duplex = mv88e6185_port_set_speed_duplex,
 	.port_set_frame_mode = mv88e6085_port_set_frame_mode,
 	.port_set_egress_floods = mv88e6352_port_set_egress_floods,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
@@ -3548,8 +3534,7 @@ static const struct mv88e6xxx_ops mv88e6131_ops = {
 	.phy_read = mv88e6185_phy_ppu_read,
 	.phy_write = mv88e6185_phy_ppu_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
-	.port_set_speed = mv88e6185_port_set_speed,
+	.port_set_speed_duplex = mv88e6185_port_set_speed_duplex,
 	.port_tag_remap = mv88e6095_port_tag_remap,
 	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
 	.port_set_egress_floods = mv88e6185_port_set_egress_floods,
@@ -3591,9 +3576,8 @@ static const struct mv88e6xxx_ops mv88e6141_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
 	.port_set_rgmii_delay = mv88e6390_port_set_rgmii_delay,
-	.port_set_speed = mv88e6341_port_set_speed,
+	.port_set_speed_duplex = mv88e6341_port_set_speed_duplex,
 	.port_max_speed_mode = mv88e6341_port_max_speed_mode,
 	.port_tag_remap = mv88e6095_port_tag_remap,
 	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
@@ -3644,8 +3628,7 @@ static const struct mv88e6xxx_ops mv88e6161_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
-	.port_set_speed = mv88e6185_port_set_speed,
+	.port_set_speed_duplex = mv88e6185_port_set_speed_duplex,
 	.port_tag_remap = mv88e6095_port_tag_remap,
 	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
 	.port_set_egress_floods = mv88e6352_port_set_egress_floods,
@@ -3687,8 +3670,7 @@ static const struct mv88e6xxx_ops mv88e6165_ops = {
 	.phy_read = mv88e6165_phy_read,
 	.phy_write = mv88e6165_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
-	.port_set_speed = mv88e6185_port_set_speed,
+	.port_set_speed_duplex = mv88e6185_port_set_speed_duplex,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
 	.port_link_state = mv88e6352_port_link_state,
@@ -3723,9 +3705,8 @@ static const struct mv88e6xxx_ops mv88e6171_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
 	.port_set_rgmii_delay = mv88e6352_port_set_rgmii_delay,
-	.port_set_speed = mv88e6185_port_set_speed,
+	.port_set_speed_duplex = mv88e6185_port_set_speed_duplex,
 	.port_tag_remap = mv88e6095_port_tag_remap,
 	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
 	.port_set_egress_floods = mv88e6352_port_set_egress_floods,
@@ -3767,9 +3748,8 @@ static const struct mv88e6xxx_ops mv88e6172_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
 	.port_set_rgmii_delay = mv88e6352_port_set_rgmii_delay,
-	.port_set_speed = mv88e6352_port_set_speed,
+	.port_set_speed_duplex = mv88e6352_port_set_speed_duplex,
 	.port_tag_remap = mv88e6095_port_tag_remap,
 	.port_set_policy = mv88e6352_port_set_policy,
 	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
@@ -3818,9 +3798,8 @@ static const struct mv88e6xxx_ops mv88e6175_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
 	.port_set_rgmii_delay = mv88e6352_port_set_rgmii_delay,
-	.port_set_speed = mv88e6185_port_set_speed,
+	.port_set_speed_duplex = mv88e6185_port_set_speed_duplex,
 	.port_tag_remap = mv88e6095_port_tag_remap,
 	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
 	.port_set_egress_floods = mv88e6352_port_set_egress_floods,
@@ -3862,9 +3841,8 @@ static const struct mv88e6xxx_ops mv88e6176_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
 	.port_set_rgmii_delay = mv88e6352_port_set_rgmii_delay,
-	.port_set_speed = mv88e6352_port_set_speed,
+	.port_set_speed_duplex = mv88e6352_port_set_speed_duplex,
 	.port_tag_remap = mv88e6095_port_tag_remap,
 	.port_set_policy = mv88e6352_port_set_policy,
 	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
@@ -3915,8 +3893,7 @@ static const struct mv88e6xxx_ops mv88e6185_ops = {
 	.phy_read = mv88e6185_phy_ppu_read,
 	.phy_write = mv88e6185_phy_ppu_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
-	.port_set_speed = mv88e6185_port_set_speed,
+	.port_set_speed_duplex = mv88e6185_port_set_speed_duplex,
 	.port_set_frame_mode = mv88e6085_port_set_frame_mode,
 	.port_set_egress_floods = mv88e6185_port_set_egress_floods,
 	.port_egress_rate_limiting = mv88e6095_port_egress_rate_limiting,
@@ -3953,9 +3930,8 @@ static const struct mv88e6xxx_ops mv88e6190_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
 	.port_set_rgmii_delay = mv88e6390_port_set_rgmii_delay,
-	.port_set_speed = mv88e6390_port_set_speed,
+	.port_set_speed_duplex = mv88e6390_port_set_speed_duplex,
 	.port_max_speed_mode = mv88e6390_port_max_speed_mode,
 	.port_tag_remap = mv88e6390_port_tag_remap,
 	.port_set_policy = mv88e6352_port_set_policy,
@@ -4012,9 +3988,8 @@ static const struct mv88e6xxx_ops mv88e6190x_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
 	.port_set_rgmii_delay = mv88e6390_port_set_rgmii_delay,
-	.port_set_speed = mv88e6390x_port_set_speed,
+	.port_set_speed_duplex = mv88e6390x_port_set_speed_duplex,
 	.port_max_speed_mode = mv88e6390x_port_max_speed_mode,
 	.port_tag_remap = mv88e6390_port_tag_remap,
 	.port_set_policy = mv88e6352_port_set_policy,
@@ -4071,9 +4046,8 @@ static const struct mv88e6xxx_ops mv88e6191_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
 	.port_set_rgmii_delay = mv88e6390_port_set_rgmii_delay,
-	.port_set_speed = mv88e6390_port_set_speed,
+	.port_set_speed_duplex = mv88e6390_port_set_speed_duplex,
 	.port_max_speed_mode = mv88e6390_port_max_speed_mode,
 	.port_tag_remap = mv88e6390_port_tag_remap,
 	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
@@ -4131,9 +4105,8 @@ static const struct mv88e6xxx_ops mv88e6240_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
 	.port_set_rgmii_delay = mv88e6352_port_set_rgmii_delay,
-	.port_set_speed = mv88e6352_port_set_speed,
+	.port_set_speed_duplex = mv88e6352_port_set_speed_duplex,
 	.port_tag_remap = mv88e6095_port_tag_remap,
 	.port_set_policy = mv88e6352_port_set_policy,
 	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
@@ -4189,9 +4162,8 @@ static const struct mv88e6xxx_ops mv88e6250_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
 	.port_set_rgmii_delay = mv88e6352_port_set_rgmii_delay,
-	.port_set_speed = mv88e6250_port_set_speed,
+	.port_set_speed_duplex = mv88e6250_port_set_speed_duplex,
 	.port_tag_remap = mv88e6095_port_tag_remap,
 	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
 	.port_set_egress_floods = mv88e6352_port_set_egress_floods,
@@ -4228,9 +4200,8 @@ static const struct mv88e6xxx_ops mv88e6290_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
 	.port_set_rgmii_delay = mv88e6390_port_set_rgmii_delay,
-	.port_set_speed = mv88e6390_port_set_speed,
+	.port_set_speed_duplex = mv88e6390_port_set_speed_duplex,
 	.port_max_speed_mode = mv88e6390_port_max_speed_mode,
 	.port_tag_remap = mv88e6390_port_tag_remap,
 	.port_set_policy = mv88e6352_port_set_policy,
@@ -4290,8 +4261,7 @@ static const struct mv88e6xxx_ops mv88e6320_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
-	.port_set_speed = mv88e6185_port_set_speed,
+	.port_set_speed_duplex = mv88e6185_port_set_speed_duplex,
 	.port_tag_remap = mv88e6095_port_tag_remap,
 	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
 	.port_set_egress_floods = mv88e6352_port_set_egress_floods,
@@ -4334,8 +4304,7 @@ static const struct mv88e6xxx_ops mv88e6321_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
-	.port_set_speed = mv88e6185_port_set_speed,
+	.port_set_speed_duplex = mv88e6185_port_set_speed_duplex,
 	.port_tag_remap = mv88e6095_port_tag_remap,
 	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
 	.port_set_egress_floods = mv88e6352_port_set_egress_floods,
@@ -4376,9 +4345,8 @@ static const struct mv88e6xxx_ops mv88e6341_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
 	.port_set_rgmii_delay = mv88e6390_port_set_rgmii_delay,
-	.port_set_speed = mv88e6341_port_set_speed,
+	.port_set_speed_duplex = mv88e6341_port_set_speed_duplex,
 	.port_max_speed_mode = mv88e6341_port_max_speed_mode,
 	.port_tag_remap = mv88e6095_port_tag_remap,
 	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
@@ -4431,9 +4399,8 @@ static const struct mv88e6xxx_ops mv88e6350_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
 	.port_set_rgmii_delay = mv88e6352_port_set_rgmii_delay,
-	.port_set_speed = mv88e6185_port_set_speed,
+	.port_set_speed_duplex = mv88e6185_port_set_speed_duplex,
 	.port_tag_remap = mv88e6095_port_tag_remap,
 	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
 	.port_set_egress_floods = mv88e6352_port_set_egress_floods,
@@ -4473,9 +4440,8 @@ static const struct mv88e6xxx_ops mv88e6351_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
 	.port_set_rgmii_delay = mv88e6352_port_set_rgmii_delay,
-	.port_set_speed = mv88e6185_port_set_speed,
+	.port_set_speed_duplex = mv88e6185_port_set_speed_duplex,
 	.port_tag_remap = mv88e6095_port_tag_remap,
 	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
 	.port_set_egress_floods = mv88e6352_port_set_egress_floods,
@@ -4519,9 +4485,8 @@ static const struct mv88e6xxx_ops mv88e6352_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
 	.port_set_rgmii_delay = mv88e6352_port_set_rgmii_delay,
-	.port_set_speed = mv88e6352_port_set_speed,
+	.port_set_speed_duplex = mv88e6352_port_set_speed_duplex,
 	.port_tag_remap = mv88e6095_port_tag_remap,
 	.port_set_policy = mv88e6352_port_set_policy,
 	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
@@ -4579,9 +4544,8 @@ static const struct mv88e6xxx_ops mv88e6390_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
 	.port_set_rgmii_delay = mv88e6390_port_set_rgmii_delay,
-	.port_set_speed = mv88e6390_port_set_speed,
+	.port_set_speed_duplex = mv88e6390_port_set_speed_duplex,
 	.port_max_speed_mode = mv88e6390_port_max_speed_mode,
 	.port_tag_remap = mv88e6390_port_tag_remap,
 	.port_set_policy = mv88e6352_port_set_policy,
@@ -4642,9 +4606,8 @@ static const struct mv88e6xxx_ops mv88e6390x_ops = {
 	.phy_read = mv88e6xxx_g2_smi_phy_read,
 	.phy_write = mv88e6xxx_g2_smi_phy_write,
 	.port_set_link = mv88e6xxx_port_set_link,
-	.port_set_duplex = mv88e6xxx_port_set_duplex,
 	.port_set_rgmii_delay = mv88e6390_port_set_rgmii_delay,
-	.port_set_speed = mv88e6390x_port_set_speed,
+	.port_set_speed_duplex = mv88e6390x_port_set_speed_duplex,
 	.port_max_speed_mode = mv88e6390x_port_max_speed_mode,
 	.port_tag_remap = mv88e6390_port_tag_remap,
 	.port_set_policy = mv88e6352_port_set_policy,
diff --git a/drivers/net/dsa/mv88e6xxx/chip.h b/drivers/net/dsa/mv88e6xxx/chip.h
index 38dc336970db..ef0028fe6772 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.h
+++ b/drivers/net/dsa/mv88e6xxx/chip.h
@@ -399,15 +399,6 @@ struct mv88e6xxx_ops {
 	 */
 	int (*port_set_link)(struct mv88e6xxx_chip *chip, int port, int link);
 
-#define DUPLEX_UNFORCED		-2
-
-	/* Port's MAC duplex mode
-	 *
-	 * Use DUPLEX_HALF or DUPLEX_FULL to force half or full duplex,
-	 * or DUPLEX_UNFORCED for normal duplex detection.
-	 */
-	int (*port_set_duplex)(struct mv88e6xxx_chip *chip, int port, int dup);
-
 #define PAUSE_ON		1
 #define PAUSE_OFF		0
 
@@ -417,13 +408,18 @@ struct mv88e6xxx_ops {
 
 #define SPEED_MAX		INT_MAX
 #define SPEED_UNFORCED		-2
+#define DUPLEX_UNFORCED		-2
 
-	/* Port's MAC speed (in Mbps)
+	/* Port's MAC speed (in Mbps) and MAC duplex mode
 	 *
 	 * Depending on the chip, 10, 100, 200, 1000, 2500, 10000 are valid.
 	 * Use SPEED_UNFORCED for normal detection, SPEED_MAX for max value.
+	 *
+	 * Use DUPLEX_HALF or DUPLEX_FULL to force half or full duplex,
+	 * or DUPLEX_UNFORCED for normal duplex detection.
 	 */
-	int (*port_set_speed)(struct mv88e6xxx_chip *chip, int port, int speed);
+	int (*port_set_speed_duplex)(struct mv88e6xxx_chip *chip, int port,
+				     int speed, int duplex);
 
 	/* What interface mode should be used for maximum speed? */
 	phy_interface_t (*port_max_speed_mode)(int port);
diff --git a/drivers/net/dsa/mv88e6xxx/port.c b/drivers/net/dsa/mv88e6xxx/port.c
index 0b43c650e100..442abb719cdc 100644
--- a/drivers/net/dsa/mv88e6xxx/port.c
+++ b/drivers/net/dsa/mv88e6xxx/port.c
@@ -162,46 +162,9 @@ int mv88e6xxx_port_set_link(struct mv88e6xxx_chip *chip, int port, int link)
 	return 0;
 }
 
-int mv88e6xxx_port_set_duplex(struct mv88e6xxx_chip *chip, int port, int dup)
-{
-	u16 reg;
-	int err;
-
-	err = mv88e6xxx_port_read(chip, port, MV88E6XXX_PORT_MAC_CTL, &reg);
-	if (err)
-		return err;
-
-	reg &= ~(MV88E6XXX_PORT_MAC_CTL_FORCE_DUPLEX |
-		 MV88E6XXX_PORT_MAC_CTL_DUPLEX_FULL);
-
-	switch (dup) {
-	case DUPLEX_HALF:
-		reg |= MV88E6XXX_PORT_MAC_CTL_FORCE_DUPLEX;
-		break;
-	case DUPLEX_FULL:
-		reg |= MV88E6XXX_PORT_MAC_CTL_FORCE_DUPLEX |
-			MV88E6XXX_PORT_MAC_CTL_DUPLEX_FULL;
-		break;
-	case DUPLEX_UNFORCED:
-		/* normal duplex detection */
-		break;
-	default:
-		return -EOPNOTSUPP;
-	}
-
-	err = mv88e6xxx_port_write(chip, port, MV88E6XXX_PORT_MAC_CTL, reg);
-	if (err)
-		return err;
-
-	dev_dbg(chip->dev, "p%d: %s %s duplex\n", port,
-		reg & MV88E6XXX_PORT_MAC_CTL_FORCE_DUPLEX ? "Force" : "Unforce",
-		reg & MV88E6XXX_PORT_MAC_CTL_DUPLEX_FULL ? "full" : "half");
-
-	return 0;
-}
-
-static int mv88e6xxx_port_set_speed(struct mv88e6xxx_chip *chip, int port,
-				    int speed, bool alt_bit, bool force_bit)
+static int mv88e6xxx_port_set_speed_duplex(struct mv88e6xxx_chip *chip,
+					   int port, int speed, bool alt_bit,
+					   bool force_bit, int duplex)
 {
 	u16 reg, ctrl;
 	int err;
@@ -239,11 +202,29 @@ static int mv88e6xxx_port_set_speed(struct mv88e6xxx_chip *chip, int port,
 		return -EOPNOTSUPP;
 	}
 
+	switch (duplex) {
+	case DUPLEX_HALF:
+		ctrl |= MV88E6XXX_PORT_MAC_CTL_FORCE_DUPLEX;
+		break;
+	case DUPLEX_FULL:
+		ctrl |= MV88E6XXX_PORT_MAC_CTL_FORCE_DUPLEX |
+			MV88E6XXX_PORT_MAC_CTL_DUPLEX_FULL;
+		break;
+	case DUPLEX_UNFORCED:
+		/* normal duplex detection */
+		break;
+	default:
+		return -EOPNOTSUPP;
+	}
+
 	err = mv88e6xxx_port_read(chip, port, MV88E6XXX_PORT_MAC_CTL, &reg);
 	if (err)
 		return err;
 
-	reg &= ~MV88E6XXX_PORT_MAC_CTL_SPEED_MASK;
+	reg &= ~(MV88E6XXX_PORT_MAC_CTL_SPEED_MASK |
+		 MV88E6XXX_PORT_MAC_CTL_FORCE_DUPLEX |
+		 MV88E6XXX_PORT_MAC_CTL_DUPLEX_FULL);
+
 	if (alt_bit)
 		reg &= ~MV88E6390_PORT_MAC_CTL_ALTSPEED;
 	if (force_bit) {
@@ -261,12 +242,16 @@ static int mv88e6xxx_port_set_speed(struct mv88e6xxx_chip *chip, int port,
 		dev_dbg(chip->dev, "p%d: Speed set to %d Mbps\n", port, speed);
 	else
 		dev_dbg(chip->dev, "p%d: Speed unforced\n", port);
+	dev_dbg(chip->dev, "p%d: %s %s duplex\n", port,
+		reg & MV88E6XXX_PORT_MAC_CTL_FORCE_DUPLEX ? "Force" : "Unforce",
+		reg & MV88E6XXX_PORT_MAC_CTL_DUPLEX_FULL ? "full" : "half");
 
 	return 0;
 }
 
 /* Support 10, 100, 200 Mbps (e.g. 88E6065 family) */
-int mv88e6065_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed)
+int mv88e6065_port_set_speed_duplex(struct mv88e6xxx_chip *chip, int port,
+				    int speed, int duplex)
 {
 	if (speed == SPEED_MAX)
 		speed = 200;
@@ -275,11 +260,13 @@ int mv88e6065_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed)
 		return -EOPNOTSUPP;
 
 	/* Setting 200 Mbps on port 0 to 3 selects 100 Mbps */
-	return mv88e6xxx_port_set_speed(chip, port, speed, false, false);
+	return mv88e6xxx_port_set_speed_duplex(chip, port, speed, false, false,
+					       duplex);
 }
 
 /* Support 10, 100, 1000 Mbps (e.g. 88E6185 family) */
-int mv88e6185_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed)
+int mv88e6185_port_set_speed_duplex(struct mv88e6xxx_chip *chip, int port,
+				    int speed, int duplex)
 {
 	if (speed == SPEED_MAX)
 		speed = 1000;
@@ -287,11 +274,13 @@ int mv88e6185_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed)
 	if (speed == 200 || speed > 1000)
 		return -EOPNOTSUPP;
 
-	return mv88e6xxx_port_set_speed(chip, port, speed, false, false);
+	return mv88e6xxx_port_set_speed_duplex(chip, port, speed, false, false,
+					       duplex);
 }
 
 /* Support 10, 100 Mbps (e.g. 88E6250 family) */
-int mv88e6250_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed)
+int mv88e6250_port_set_speed_duplex(struct mv88e6xxx_chip *chip, int port,
+				    int speed, int duplex)
 {
 	if (speed == SPEED_MAX)
 		speed = 100;
@@ -299,11 +288,13 @@ int mv88e6250_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed)
 	if (speed > 100)
 		return -EOPNOTSUPP;
 
-	return mv88e6xxx_port_set_speed(chip, port, speed, false, false);
+	return mv88e6xxx_port_set_speed_duplex(chip, port, speed, false, false,
+					       duplex);
 }
 
 /* Support 10, 100, 200, 1000, 2500 Mbps (e.g. 88E6341) */
-int mv88e6341_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed)
+int mv88e6341_port_set_speed_duplex(struct mv88e6xxx_chip *chip, int port,
+				    int speed, int duplex)
 {
 	if (speed == SPEED_MAX)
 		speed = port < 5 ? 1000 : 2500;
@@ -317,7 +308,8 @@ int mv88e6341_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed)
 	if (speed == 2500 && port < 5)
 		return -EOPNOTSUPP;
 
-	return mv88e6xxx_port_set_speed(chip, port, speed, !port, true);
+	return mv88e6xxx_port_set_speed_duplex(chip, port, speed, !port, true,
+					       duplex);
 }
 
 phy_interface_t mv88e6341_port_max_speed_mode(int port)
@@ -329,7 +321,8 @@ phy_interface_t mv88e6341_port_max_speed_mode(int port)
 }
 
 /* Support 10, 100, 200, 1000 Mbps (e.g. 88E6352 family) */
-int mv88e6352_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed)
+int mv88e6352_port_set_speed_duplex(struct mv88e6xxx_chip *chip, int port,
+				    int speed, int duplex)
 {
 	if (speed == SPEED_MAX)
 		speed = 1000;
@@ -340,11 +333,13 @@ int mv88e6352_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed)
 	if (speed == 200 && port < 5)
 		return -EOPNOTSUPP;
 
-	return mv88e6xxx_port_set_speed(chip, port, speed, true, false);
+	return mv88e6xxx_port_set_speed_duplex(chip, port, speed, true, false,
+					       duplex);
 }
 
 /* Support 10, 100, 200, 1000, 2500 Mbps (e.g. 88E6390) */
-int mv88e6390_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed)
+int mv88e6390_port_set_speed_duplex(struct mv88e6xxx_chip *chip, int port,
+				    int speed, int duplex)
 {
 	if (speed == SPEED_MAX)
 		speed = port < 9 ? 1000 : 2500;
@@ -358,7 +353,8 @@ int mv88e6390_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed)
 	if (speed == 2500 && port < 9)
 		return -EOPNOTSUPP;
 
-	return mv88e6xxx_port_set_speed(chip, port, speed, true, true);
+	return mv88e6xxx_port_set_speed_duplex(chip, port, speed, true, true,
+					       duplex);
 }
 
 phy_interface_t mv88e6390_port_max_speed_mode(int port)
@@ -370,7 +366,8 @@ phy_interface_t mv88e6390_port_max_speed_mode(int port)
 }
 
 /* Support 10, 100, 200, 1000, 2500, 10000 Mbps (e.g. 88E6190X) */
-int mv88e6390x_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed)
+int mv88e6390x_port_set_speed_duplex(struct mv88e6xxx_chip *chip, int port,
+				     int speed, int duplex)
 {
 	if (speed == SPEED_MAX)
 		speed = port < 9 ? 1000 : 10000;
@@ -381,7 +378,8 @@ int mv88e6390x_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed)
 	if (speed >= 2500 && port < 9)
 		return -EOPNOTSUPP;
 
-	return mv88e6xxx_port_set_speed(chip, port, speed, true, true);
+	return mv88e6xxx_port_set_speed_duplex(chip, port, speed, true, true,
+					       duplex);
 }
 
 phy_interface_t mv88e6390x_port_max_speed_mode(int port)
diff --git a/drivers/net/dsa/mv88e6xxx/port.h b/drivers/net/dsa/mv88e6xxx/port.h
index 0ec4327c2b42..1d18426b7ff6 100644
--- a/drivers/net/dsa/mv88e6xxx/port.h
+++ b/drivers/net/dsa/mv88e6xxx/port.h
@@ -298,15 +298,20 @@ int mv88e6390_port_set_rgmii_delay(struct mv88e6xxx_chip *chip, int port,
 
 int mv88e6xxx_port_set_link(struct mv88e6xxx_chip *chip, int port, int link);
 
-int mv88e6xxx_port_set_duplex(struct mv88e6xxx_chip *chip, int port, int dup);
-
-int mv88e6065_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed);
-int mv88e6185_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed);
-int mv88e6250_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed);
-int mv88e6341_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed);
-int mv88e6352_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed);
-int mv88e6390_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed);
-int mv88e6390x_port_set_speed(struct mv88e6xxx_chip *chip, int port, int speed);
+int mv88e6065_port_set_speed_duplex(struct mv88e6xxx_chip *chip, int port,
+				    int speed, int duplex);
+int mv88e6185_port_set_speed_duplex(struct mv88e6xxx_chip *chip, int port,
+				    int speed, int duplex);
+int mv88e6250_port_set_speed_duplex(struct mv88e6xxx_chip *chip, int port,
+				    int speed, int duplex);
+int mv88e6341_port_set_speed_duplex(struct mv88e6xxx_chip *chip, int port,
+				    int speed, int duplex);
+int mv88e6352_port_set_speed_duplex(struct mv88e6xxx_chip *chip, int port,
+				    int speed, int duplex);
+int mv88e6390_port_set_speed_duplex(struct mv88e6xxx_chip *chip, int port,
+				    int speed, int duplex);
+int mv88e6390x_port_set_speed_duplex(struct mv88e6xxx_chip *chip, int port,
+				     int speed, int duplex);
 
 phy_interface_t mv88e6341_port_max_speed_mode(int port);
 phy_interface_t mv88e6390_port_max_speed_mode(int port);

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

The port_link_state method is only used by mv88e6xxx_port_setup_mac(),
which is now only called during port setup, rather than also being
called via phylink's mac_config method.

Remove this now unnecessary optimisation, which allows us to remove the
port_link_state methods as well.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/dsa/mv88e6xxx/chip.c |  46 ----------
 drivers/net/dsa/mv88e6xxx/chip.h |   3 -
 drivers/net/dsa/mv88e6xxx/port.c | 177 ---------------------------------------
 drivers/net/dsa/mv88e6xxx/port.h |   6 --
 4 files changed, 232 deletions(-)

diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
index 2bc686f12f2a..8888fd79dbfc 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.c
+++ b/drivers/net/dsa/mv88e6xxx/chip.c
@@ -423,30 +423,11 @@ static int mv88e6xxx_port_setup_mac(struct mv88e6xxx_chip *chip, int port,
 				    int link, int speed, int duplex, int pause,
 				    phy_interface_t mode)
 {
-	struct phylink_link_state state;
 	int err;
 
 	if (!chip->info->ops->port_set_link)
 		return 0;
 
-	if (!chip->info->ops->port_link_state)
-		return 0;
-
-	err = chip->info->ops->port_link_state(chip, port, &state);
-	if (err)
-		return err;
-
-	/* Has anything actually changed? We don't expect the
-	 * interface mode to change without one of the other
-	 * parameters also changing
-	 */
-	if (state.link == link &&
-	    state.speed == speed &&
-	    state.duplex == duplex &&
-	    (state.interface == mode ||
-	     state.interface == PHY_INTERFACE_MODE_NA))
-		return 0;
-
 	/* Port's MAC control must not be changed unless the link is down */
 	err = chip->info->ops->port_set_link(chip, port, LINK_FORCED_DOWN);
 	if (err)
@@ -3401,7 +3382,6 @@ static const struct mv88e6xxx_ops mv88e6085_ops = {
 	.port_pause_limit = mv88e6097_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6185_port_get_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
 	.stats_snapshot = mv88e6xxx_g1_stats_snapshot,
@@ -3435,7 +3415,6 @@ static const struct mv88e6xxx_ops mv88e6095_ops = {
 	.port_set_frame_mode = mv88e6085_port_set_frame_mode,
 	.port_set_egress_floods = mv88e6185_port_set_egress_floods,
 	.port_set_upstream_port = mv88e6095_port_set_upstream_port,
-	.port_link_state = mv88e6185_port_link_state,
 	.port_get_cmode = mv88e6185_port_get_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
 	.stats_snapshot = mv88e6xxx_g1_stats_snapshot,
@@ -3471,7 +3450,6 @@ static const struct mv88e6xxx_ops mv88e6097_ops = {
 	.port_pause_limit = mv88e6097_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6185_port_get_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
 	.stats_snapshot = mv88e6xxx_g1_stats_snapshot,
@@ -3505,7 +3483,6 @@ static const struct mv88e6xxx_ops mv88e6123_ops = {
 	.port_set_egress_floods = mv88e6352_port_set_egress_floods,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6185_port_get_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
 	.stats_snapshot = mv88e6320_g1_stats_snapshot,
@@ -3544,7 +3521,6 @@ static const struct mv88e6xxx_ops mv88e6131_ops = {
 	.port_egress_rate_limiting = mv88e6097_port_egress_rate_limiting,
 	.port_pause_limit = mv88e6097_port_pause_limit,
 	.port_set_pause = mv88e6185_port_set_pause,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6185_port_get_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
 	.stats_snapshot = mv88e6xxx_g1_stats_snapshot,
@@ -3588,7 +3564,6 @@ static const struct mv88e6xxx_ops mv88e6141_ops = {
 	.port_pause_limit = mv88e6097_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
 	.port_set_cmode = mv88e6341_port_set_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
@@ -3638,7 +3613,6 @@ static const struct mv88e6xxx_ops mv88e6161_ops = {
 	.port_pause_limit = mv88e6097_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6185_port_get_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
 	.stats_snapshot = mv88e6xxx_g1_stats_snapshot,
@@ -3673,7 +3647,6 @@ static const struct mv88e6xxx_ops mv88e6165_ops = {
 	.port_set_speed_duplex = mv88e6185_port_set_speed_duplex,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6185_port_get_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
 	.stats_snapshot = mv88e6xxx_g1_stats_snapshot,
@@ -3716,7 +3689,6 @@ static const struct mv88e6xxx_ops mv88e6171_ops = {
 	.port_pause_limit = mv88e6097_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
 	.stats_snapshot = mv88e6320_g1_stats_snapshot,
@@ -3760,7 +3732,6 @@ static const struct mv88e6xxx_ops mv88e6172_ops = {
 	.port_pause_limit = mv88e6097_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
 	.stats_snapshot = mv88e6320_g1_stats_snapshot,
@@ -3809,7 +3780,6 @@ static const struct mv88e6xxx_ops mv88e6175_ops = {
 	.port_pause_limit = mv88e6097_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
 	.stats_snapshot = mv88e6320_g1_stats_snapshot,
@@ -3853,7 +3823,6 @@ static const struct mv88e6xxx_ops mv88e6176_ops = {
 	.port_pause_limit = mv88e6097_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
 	.stats_snapshot = mv88e6320_g1_stats_snapshot,
@@ -3899,7 +3868,6 @@ static const struct mv88e6xxx_ops mv88e6185_ops = {
 	.port_egress_rate_limiting = mv88e6095_port_egress_rate_limiting,
 	.port_set_upstream_port = mv88e6095_port_set_upstream_port,
 	.port_set_pause = mv88e6185_port_set_pause,
-	.port_link_state = mv88e6185_port_link_state,
 	.port_get_cmode = mv88e6185_port_get_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
 	.stats_snapshot = mv88e6xxx_g1_stats_snapshot,
@@ -3941,7 +3909,6 @@ static const struct mv88e6xxx_ops mv88e6190_ops = {
 	.port_pause_limit = mv88e6390_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
 	.port_set_cmode = mv88e6390_port_set_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
@@ -3999,7 +3966,6 @@ static const struct mv88e6xxx_ops mv88e6190x_ops = {
 	.port_pause_limit = mv88e6390_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
 	.port_set_cmode = mv88e6390x_port_set_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
@@ -4056,7 +4022,6 @@ static const struct mv88e6xxx_ops mv88e6191_ops = {
 	.port_pause_limit = mv88e6390_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
 	.port_set_cmode = mv88e6390_port_set_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
@@ -4117,7 +4082,6 @@ static const struct mv88e6xxx_ops mv88e6240_ops = {
 	.port_pause_limit = mv88e6097_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
 	.stats_snapshot = mv88e6320_g1_stats_snapshot,
@@ -4171,7 +4135,6 @@ static const struct mv88e6xxx_ops mv88e6250_ops = {
 	.port_egress_rate_limiting = mv88e6097_port_egress_rate_limiting,
 	.port_pause_limit = mv88e6097_port_pause_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6250_port_link_state,
 	.stats_snapshot = mv88e6320_g1_stats_snapshot,
 	.stats_set_histogram = mv88e6095_g1_stats_set_histogram,
 	.stats_get_sset_count = mv88e6250_stats_get_sset_count,
@@ -4211,7 +4174,6 @@ static const struct mv88e6xxx_ops mv88e6290_ops = {
 	.port_pause_limit = mv88e6390_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
 	.port_set_cmode = mv88e6390_port_set_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
@@ -4271,7 +4233,6 @@ static const struct mv88e6xxx_ops mv88e6320_ops = {
 	.port_pause_limit = mv88e6097_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
 	.stats_snapshot = mv88e6320_g1_stats_snapshot,
@@ -4314,7 +4275,6 @@ static const struct mv88e6xxx_ops mv88e6321_ops = {
 	.port_pause_limit = mv88e6097_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
 	.stats_snapshot = mv88e6320_g1_stats_snapshot,
@@ -4357,7 +4317,6 @@ static const struct mv88e6xxx_ops mv88e6341_ops = {
 	.port_pause_limit = mv88e6097_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
 	.port_set_cmode = mv88e6341_port_set_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
@@ -4410,7 +4369,6 @@ static const struct mv88e6xxx_ops mv88e6350_ops = {
 	.port_pause_limit = mv88e6097_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
 	.stats_snapshot = mv88e6320_g1_stats_snapshot,
@@ -4451,7 +4409,6 @@ static const struct mv88e6xxx_ops mv88e6351_ops = {
 	.port_pause_limit = mv88e6097_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
 	.stats_snapshot = mv88e6320_g1_stats_snapshot,
@@ -4497,7 +4454,6 @@ static const struct mv88e6xxx_ops mv88e6352_ops = {
 	.port_pause_limit = mv88e6097_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
 	.stats_snapshot = mv88e6320_g1_stats_snapshot,
@@ -4557,7 +4513,6 @@ static const struct mv88e6xxx_ops mv88e6390_ops = {
 	.port_pause_limit = mv88e6390_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
 	.port_set_cmode = mv88e6390_port_set_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
@@ -4619,7 +4574,6 @@ static const struct mv88e6xxx_ops mv88e6390x_ops = {
 	.port_pause_limit = mv88e6390_port_pause_limit,
 	.port_disable_learn_limit = mv88e6xxx_port_disable_learn_limit,
 	.port_disable_pri_override = mv88e6xxx_port_disable_pri_override,
-	.port_link_state = mv88e6352_port_link_state,
 	.port_get_cmode = mv88e6352_port_get_cmode,
 	.port_set_cmode = mv88e6390x_port_set_cmode,
 	.port_setup_message_port = mv88e6xxx_setup_message_port,
diff --git a/drivers/net/dsa/mv88e6xxx/chip.h b/drivers/net/dsa/mv88e6xxx/chip.h
index ef0028fe6772..50c4d1343b0f 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.h
+++ b/drivers/net/dsa/mv88e6xxx/chip.h
@@ -458,9 +458,6 @@ struct mv88e6xxx_ops {
 	 */
 	int (*port_set_upstream_port)(struct mv88e6xxx_chip *chip, int port,
 				      int upstream_port);
-	/* Return the port link state, as required by phylink */
-	int (*port_link_state)(struct mv88e6xxx_chip *chip, int port,
-			       struct phylink_link_state *state);
 
 	/* Snapshot the statistics for a port. The statistics can then
 	 * be read back a leisure but still with a consistent view.
diff --git a/drivers/net/dsa/mv88e6xxx/port.c b/drivers/net/dsa/mv88e6xxx/port.c
index 442abb719cdc..8128dc607cf4 100644
--- a/drivers/net/dsa/mv88e6xxx/port.c
+++ b/drivers/net/dsa/mv88e6xxx/port.c
@@ -584,183 +584,6 @@ int mv88e6352_port_get_cmode(struct mv88e6xxx_chip *chip, int port, u8 *cmode)
 	return 0;
 }
 
-int mv88e6250_port_link_state(struct mv88e6xxx_chip *chip, int port,
-			      struct phylink_link_state *state)
-{
-	int err;
-	u16 reg;
-
-	err = mv88e6xxx_port_read(chip, port, MV88E6XXX_PORT_STS, &reg);
-	if (err)
-		return err;
-
-	if (port < 5) {
-		switch (reg & MV88E6250_PORT_STS_PORTMODE_MASK) {
-		case MV88E6250_PORT_STS_PORTMODE_PHY_10_HALF:
-			state->speed = SPEED_10;
-			state->duplex = DUPLEX_HALF;
-			break;
-		case MV88E6250_PORT_STS_PORTMODE_PHY_100_HALF:
-			state->speed = SPEED_100;
-			state->duplex = DUPLEX_HALF;
-			break;
-		case MV88E6250_PORT_STS_PORTMODE_PHY_10_FULL:
-			state->speed = SPEED_10;
-			state->duplex = DUPLEX_FULL;
-			break;
-		case MV88E6250_PORT_STS_PORTMODE_PHY_100_FULL:
-			state->speed = SPEED_100;
-			state->duplex = DUPLEX_FULL;
-			break;
-		default:
-			state->speed = SPEED_UNKNOWN;
-			state->duplex = DUPLEX_UNKNOWN;
-			break;
-		}
-	} else {
-		switch (reg & MV88E6250_PORT_STS_PORTMODE_MASK) {
-		case MV88E6250_PORT_STS_PORTMODE_MII_10_HALF:
-			state->speed = SPEED_10;
-			state->duplex = DUPLEX_HALF;
-			break;
-		case MV88E6250_PORT_STS_PORTMODE_MII_100_HALF:
-			state->speed = SPEED_100;
-			state->duplex = DUPLEX_HALF;
-			break;
-		case MV88E6250_PORT_STS_PORTMODE_MII_10_FULL:
-			state->speed = SPEED_10;
-			state->duplex = DUPLEX_FULL;
-			break;
-		case MV88E6250_PORT_STS_PORTMODE_MII_100_FULL:
-			state->speed = SPEED_100;
-			state->duplex = DUPLEX_FULL;
-			break;
-		default:
-			state->speed = SPEED_UNKNOWN;
-			state->duplex = DUPLEX_UNKNOWN;
-			break;
-		}
-	}
-
-	state->link = !!(reg & MV88E6250_PORT_STS_LINK);
-	state->an_enabled = 1;
-	state->an_complete = state->link;
-	state->interface = PHY_INTERFACE_MODE_NA;
-
-	return 0;
-}
-
-int mv88e6352_port_link_state(struct mv88e6xxx_chip *chip, int port,
-			      struct phylink_link_state *state)
-{
-	int err;
-	u16 reg;
-
-	switch (chip->ports[port].cmode) {
-	case MV88E6XXX_PORT_STS_CMODE_RGMII:
-		err = mv88e6xxx_port_read(chip, port, MV88E6XXX_PORT_MAC_CTL,
-					  &reg);
-		if (err)
-			return err;
-
-		if ((reg & MV88E6XXX_PORT_MAC_CTL_RGMII_DELAY_RXCLK) &&
-		    (reg & MV88E6XXX_PORT_MAC_CTL_RGMII_DELAY_TXCLK))
-			state->interface = PHY_INTERFACE_MODE_RGMII_ID;
-		else if (reg & MV88E6XXX_PORT_MAC_CTL_RGMII_DELAY_RXCLK)
-			state->interface = PHY_INTERFACE_MODE_RGMII_RXID;
-		else if (reg & MV88E6XXX_PORT_MAC_CTL_RGMII_DELAY_TXCLK)
-			state->interface = PHY_INTERFACE_MODE_RGMII_TXID;
-		else
-			state->interface = PHY_INTERFACE_MODE_RGMII;
-		break;
-	case MV88E6XXX_PORT_STS_CMODE_1000BASEX:
-		state->interface = PHY_INTERFACE_MODE_1000BASEX;
-		break;
-	case MV88E6XXX_PORT_STS_CMODE_SGMII:
-		state->interface = PHY_INTERFACE_MODE_SGMII;
-		break;
-	case MV88E6XXX_PORT_STS_CMODE_2500BASEX:
-		state->interface = PHY_INTERFACE_MODE_2500BASEX;
-		break;
-	case MV88E6XXX_PORT_STS_CMODE_XAUI:
-		state->interface = PHY_INTERFACE_MODE_XAUI;
-		break;
-	case MV88E6XXX_PORT_STS_CMODE_RXAUI:
-		state->interface = PHY_INTERFACE_MODE_RXAUI;
-		break;
-	default:
-		/* we do not support other cmode values here */
-		state->interface = PHY_INTERFACE_MODE_NA;
-	}
-
-	err = mv88e6xxx_port_read(chip, port, MV88E6XXX_PORT_STS, &reg);
-	if (err)
-		return err;
-
-	switch (reg & MV88E6XXX_PORT_STS_SPEED_MASK) {
-	case MV88E6XXX_PORT_STS_SPEED_10:
-		state->speed = SPEED_10;
-		break;
-	case MV88E6XXX_PORT_STS_SPEED_100:
-		state->speed = SPEED_100;
-		break;
-	case MV88E6XXX_PORT_STS_SPEED_1000:
-		state->speed = SPEED_1000;
-		break;
-	case MV88E6XXX_PORT_STS_SPEED_10000:
-		if ((reg & MV88E6XXX_PORT_STS_CMODE_MASK) ==
-		    MV88E6XXX_PORT_STS_CMODE_2500BASEX)
-			state->speed = SPEED_2500;
-		else
-			state->speed = SPEED_10000;
-		break;
-	}
-
-	state->duplex = reg & MV88E6XXX_PORT_STS_DUPLEX ?
-			DUPLEX_FULL : DUPLEX_HALF;
-	state->link = !!(reg & MV88E6XXX_PORT_STS_LINK);
-	state->an_enabled = 1;
-	state->an_complete = state->link;
-
-	return 0;
-}
-
-int mv88e6185_port_link_state(struct mv88e6xxx_chip *chip, int port,
-			      struct phylink_link_state *state)
-{
-	if (state->interface == PHY_INTERFACE_MODE_1000BASEX) {
-		u8 cmode = chip->ports[port].cmode;
-
-		/* When a port is in "Cross-chip serdes" mode, it uses
-		 * 1000Base-X full duplex mode, but there is no automatic
-		 * link detection. Use the sync OK status for link (as it
-		 * would do for 1000Base-X mode.)
-		 */
-		if (cmode == MV88E6185_PORT_STS_CMODE_SERDES) {
-			u16 mac;
-			int err;
-
-			err = mv88e6xxx_port_read(chip, port,
-						  MV88E6XXX_PORT_MAC_CTL, &mac);
-			if (err)
-				return err;
-
-			state->link = !!(mac & MV88E6185_PORT_MAC_CTL_SYNC_OK);
-			state->an_enabled = 1;
-			state->an_complete =
-				!!(mac & MV88E6185_PORT_MAC_CTL_AN_DONE);
-			state->duplex =
-				state->link ? DUPLEX_FULL : DUPLEX_UNKNOWN;
-			state->speed =
-				state->link ? SPEED_1000 : SPEED_UNKNOWN;
-
-			return 0;
-		}
-	}
-
-	return mv88e6352_port_link_state(chip, port, state);
-}
-
 /* Offset 0x02: Jamming Control
  *
  * Do not limit the period of time that this port can be paused for by
diff --git a/drivers/net/dsa/mv88e6xxx/port.h b/drivers/net/dsa/mv88e6xxx/port.h
index 1d18426b7ff6..44d76ac973f6 100644
--- a/drivers/net/dsa/mv88e6xxx/port.h
+++ b/drivers/net/dsa/mv88e6xxx/port.h
@@ -364,12 +364,6 @@ int mv88e6390x_port_set_cmode(struct mv88e6xxx_chip *chip, int port,
 			      phy_interface_t mode);
 int mv88e6185_port_get_cmode(struct mv88e6xxx_chip *chip, int port, u8 *cmode);
 int mv88e6352_port_get_cmode(struct mv88e6xxx_chip *chip, int port, u8 *cmode);
-int mv88e6185_port_link_state(struct mv88e6xxx_chip *chip, int port,
-			      struct phylink_link_state *state);
-int mv88e6250_port_link_state(struct mv88e6xxx_chip *chip, int port,
-			      struct phylink_link_state *state);
-int mv88e6352_port_link_state(struct mv88e6xxx_chip *chip, int port,
-			      struct phylink_link_state *state);
 int mv88e6xxx_port_set_map_da(struct mv88e6xxx_chip *chip, int port);
 int mv88e6095_port_set_upstream_port(struct mv88e6xxx_chip *chip, int port,
 				     int upstream_port);

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Use the status of the PHY_DETECT bit to determine whether we need to
force the MAC settings in mac_link_up() and mac_link_down().

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/dsa/mv88e6xxx/chip.c | 53 ++++++++++++++++++++++------------------
 1 file changed, 29 insertions(+), 24 deletions(-)

diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
index 8888fd79dbfc..6c9c89818082 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.c
+++ b/drivers/net/dsa/mv88e6xxx/chip.c
@@ -464,6 +464,22 @@ static int mv88e6xxx_phy_is_internal(struct dsa_switch *ds, int port)
 	return port < chip->info->num_internal_phys;
 }
 
+static int mv88e6xxx_port_ppu_updates(struct mv88e6xxx_chip *chip, int port)
+{
+	u16 reg;
+	int err;
+
+	err = mv88e6xxx_port_read(chip, port, MV88E6XXX_PORT_STS, &reg);
+	if (err) {
+		dev_err(chip->dev,
+			"p%d: %s: failed to read port status\n",
+			port, __func__);
+		return err;
+	}
+
+	return !!(reg & MV88E6XXX_PORT_STS_PHY_DETECT);
+}
+
 static int mv88e6xxx_serdes_pcs_get_state(struct dsa_switch *ds, int port,
 					  struct phylink_link_state *state)
 {
@@ -692,20 +708,14 @@ static void mv88e6xxx_mac_link_down(struct dsa_switch *ds, int port,
 
 	ops = chip->info->ops;
 
-	/* Internal PHYs propagate their configuration directly to the MAC.
-	 * External PHYs depend on whether the PPU is enabled for this port.
-	 * FIXME: we should be using the PPU enable state here. What about
-	 * an automedia port?
-	 */
-	if (!mv88e6xxx_phy_is_internal(ds, port) && ops->port_set_link) {
-		mv88e6xxx_reg_lock(chip);
+	mv88e6xxx_reg_lock(chip);
+	if (!mv88e6xxx_port_ppu_updates(chip, port) && ops->port_set_link)
 		err = ops->port_set_link(chip, port, LINK_FORCED_DOWN);
-		mv88e6xxx_reg_unlock(chip);
+	mv88e6xxx_reg_unlock(chip);
 
-		if (err)
-			dev_err(chip->dev,
-				"p%d: failed to force MAC link down\n", port);
-	}
+	if (err)
+		dev_err(chip->dev,
+			"p%d: failed to force MAC link down\n", port);
 }
 
 static void mv88e6xxx_mac_link_up(struct dsa_switch *ds, int port,
@@ -720,13 +730,8 @@ static void mv88e6xxx_mac_link_up(struct dsa_switch *ds, int port,
 
 	ops = chip->info->ops;
 
-	/* Internal PHYs propagate their configuration directly to the MAC.
-	 * External PHYs depend on whether the PPU is enabled for this port.
-	 * FIXME: we should be using the PPU enable state here. What about
-	 * an automedia port?
-	 */
-	if (!mv88e6xxx_phy_is_internal(ds, port)) {
-		mv88e6xxx_reg_lock(chip);
+	mv88e6xxx_reg_lock(chip);
+	if (!mv88e6xxx_port_ppu_updates(chip, port)) {
 		/* FIXME: for an automedia port, should we force the link
 		 * down here - what if the link comes up due to "other" media
 		 * while we're bringing the port up, how is the exclusivity
@@ -747,13 +752,13 @@ static void mv88e6xxx_mac_link_up(struct dsa_switch *ds, int port,
 
 		if (ops->port_set_link)
 			err = ops->port_set_link(chip, port, LINK_FORCED_UP);
+	}
 error:
-		mv88e6xxx_reg_unlock(chip);
+	mv88e6xxx_reg_unlock(chip);
 
-		if (err && err != -EOPNOTSUPP)
-			dev_err(ds->dev,
-				"p%d: failed to configure MAC link up\n", port);
-	}
+	if (err && err != -EOPNOTSUPP)
+		dev_err(ds->dev,
+			"p%d: failed to configure MAC link up\n", port);
 }

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Add APIs for modifying a MDIO device register, similar to the existing
phy_modify() group of functions, but at mdiobus level instead.  Adapt
__phy_modify_changed() to use the new mdiobus level helper.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/mdio_bus.c | 55 ++++++++++++++++++++++++++++++++++++++++++++++
 drivers/net/phy/phy-core.c | 31 --------------------------
 include/linux/mdio.h       |  4 ++++
 include/linux/phy.h        | 19 ++++++++++++++++
 4 files changed, 78 insertions(+), 31 deletions(-)

diff --git a/drivers/net/phy/mdio_bus.c b/drivers/net/phy/mdio_bus.c
index 9bb9f37f21dc..587eb5663d34 100644
--- a/drivers/net/phy/mdio_bus.c
+++ b/drivers/net/phy/mdio_bus.c
@@ -807,6 +807,38 @@ int __mdiobus_write(struct mii_bus *bus, int addr, u32 regnum, u16 val)
 }
 EXPORT_SYMBOL(__mdiobus_write);
 
+/**
+ * __mdiobus_modify_changed - Unlocked version of the mdiobus_modify function
+ * @bus: the mii_bus struct
+ * @addr: the phy address
+ * @regnum: register number to modify
+ * @mask: bit mask of bits to clear
+ * @set: bit mask of bits to set
+ *
+ * Read, modify, and if any change, write the register value back to the
+ * device. Any error returns a negative number.
+ *
+ * NOTE: MUST NOT be called from interrupt context.
+ */
+int __mdiobus_modify_changed(struct mii_bus *bus, int addr, u32 regnum,
+			     u16 mask, u16 set)
+{
+	int new, ret;
+
+	ret = __mdiobus_read(bus, addr, regnum);
+	if (ret < 0)
+		return ret;
+
+	new = (ret & ~mask) | set;
+	if (new == ret)
+		return 0;
+
+	ret = __mdiobus_write(bus, addr, regnum, new);
+
+	return ret < 0 ? ret : 1;
+}
+EXPORT_SYMBOL_GPL(__mdiobus_modify_changed);
+
 /**
  * mdiobus_read_nested - Nested version of the mdiobus_read function
  * @bus: the mii_bus struct
@@ -911,6 +943,29 @@ int mdiobus_write(struct mii_bus *bus, int addr, u32 regnum, u16 val)
 }
 EXPORT_SYMBOL(mdiobus_write);
 
+/**
+ * mdiobus_modify - Convenience function for modifying a given mdio device
+ *	register
+ * @bus: the mii_bus struct
+ * @addr: the phy address
+ * @regnum: register number to write
+ * @mask: bit mask of bits to clear
+ * @set: bit mask of bits to set
+ */
+int mdiobus_modify(struct mii_bus *bus, int addr, u32 regnum, u16 mask, u16 set)
+{
+	int err;
+
+	BUG_ON(in_interrupt());
+
+	mutex_lock(&bus->mdio_lock);
+	err = __mdiobus_modify_changed(bus, addr, regnum, mask, set);
+	mutex_unlock(&bus->mdio_lock);
+
+	return err < 0 ? err : 0;
+}
+EXPORT_SYMBOL_GPL(mdiobus_modify);
+
 /**
  * mdio_bus_match - determine if given MDIO driver supports the given
  *		    MDIO device
diff --git a/drivers/net/phy/phy-core.c b/drivers/net/phy/phy-core.c
index a4d2d59fceca..a2d5220ed6e4 100644
--- a/drivers/net/phy/phy-core.c
+++ b/drivers/net/phy/phy-core.c
@@ -488,37 +488,6 @@ int phy_write_mmd(struct phy_device *phydev, int devad, u32 regnum, u16 val)
 }
 EXPORT_SYMBOL(phy_write_mmd);
 
-/**
- * __phy_modify_changed() - Convenience function for modifying a PHY register
- * @phydev: a pointer to a &struct phy_device
- * @regnum: register number
- * @mask: bit mask of bits to clear
- * @set: bit mask of bits to set
- *
- * Unlocked helper function which allows a PHY register to be modified as
- * new register value = (old register value & ~mask) | set
- *
- * Returns negative errno, 0 if there was no change, and 1 in case of change
- */
-int __phy_modify_changed(struct phy_device *phydev, u32 regnum, u16 mask,
-			 u16 set)
-{
-	int new, ret;
-
-	ret = __phy_read(phydev, regnum);
-	if (ret < 0)
-		return ret;
-
-	new = (ret & ~mask) | set;
-	if (new == ret)
-		return 0;
-
-	ret = __phy_write(phydev, regnum, new);
-
-	return ret < 0 ? ret : 1;
-}
-EXPORT_SYMBOL_GPL(__phy_modify_changed);
-
 /**
  * phy_modify_changed - Function for modifying a PHY register
  * @phydev: the phy_device struct
diff --git a/include/linux/mdio.h b/include/linux/mdio.h
index a7604248777b..917e4bb2ed71 100644
--- a/include/linux/mdio.h
+++ b/include/linux/mdio.h
@@ -316,11 +316,15 @@ static inline void mii_10gbt_stat_mod_linkmode_lpa_t(unsigned long *advertising,
 
 int __mdiobus_read(struct mii_bus *bus, int addr, u32 regnum);
 int __mdiobus_write(struct mii_bus *bus, int addr, u32 regnum, u16 val);
+int __mdiobus_modify_changed(struct mii_bus *bus, int addr, u32 regnum,
+			     u16 mask, u16 set);
 
 int mdiobus_read(struct mii_bus *bus, int addr, u32 regnum);
 int mdiobus_read_nested(struct mii_bus *bus, int addr, u32 regnum);
 int mdiobus_write(struct mii_bus *bus, int addr, u32 regnum, u16 val);
 int mdiobus_write_nested(struct mii_bus *bus, int addr, u32 regnum, u16 val);
+int mdiobus_modify(struct mii_bus *bus, int addr, u32 regnum, u16 mask,
+		   u16 set);
 
 int mdiobus_register_device(struct mdio_device *mdiodev);
 int mdiobus_unregister_device(struct mdio_device *mdiodev);
diff --git a/include/linux/phy.h b/include/linux/phy.h
index ac956ea1a87c..8f73e4ea288c 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -752,6 +752,25 @@ static inline int __phy_write(struct phy_device *phydev, u32 regnum, u16 val)
 			       val);
 }
 
+/**
+ * __phy_modify_changed() - Convenience function for modifying a PHY register
+ * @phydev: a pointer to a &struct phy_device
+ * @regnum: register number
+ * @mask: bit mask of bits to clear
+ * @set: bit mask of bits to set
+ *
+ * Unlocked helper function which allows a PHY register to be modified as
+ * new register value = (old register value & ~mask) | set
+ *
+ * Returns negative errno, 0 if there was no change, and 1 in case of change
+ */
+static inline int __phy_modify_changed(struct phy_device *phydev, u32 regnum,
+				       u16 mask, u16 set)
+{
+	return __mdiobus_modify_changed(phydev->mdio.bus, phydev->mdio.addr,
+					regnum, mask, set);
+}
+
 /**
  * phy_read_mmd - Convenience function for reading a register
  * from an MMD on a given PHY.

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Implement helpers for PCS accessed via the MII bus using 802.3 clause
22 cycles, conforming to 802.3 clause 37 and Cisco SGMII specifications
for the advertisement word.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/phylink.c | 205 ++++++++++++++++++++++++++++++++++++++++++++++
 include/linux/phylink.h   |   6 ++
 2 files changed, 211 insertions(+)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index bf5b5026eff4..23a5e68d9222 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -2063,4 +2063,209 @@ void phylink_helper_basex_speed(struct phylink_link_state *state)
 }
 EXPORT_SYMBOL_GPL(phylink_helper_basex_speed);
 
+static void phylink_decode_c37_word(struct phylink_link_state *state,
+				    uint16_t config_reg, int speed)
+{
+	bool tx_pause, rx_pause;
+	int fd_bit;
+
+	if (speed == SPEED_2500)
+		fd_bit = ETHTOOL_LINK_MODE_2500baseX_Full_BIT;
+	else
+		fd_bit = ETHTOOL_LINK_MODE_1000baseX_Full_BIT;
+
+	mii_lpa_mod_linkmode_x(state->lp_advertising, config_reg, fd_bit);
+
+	if (linkmode_test_bit(fd_bit, state->advertising) &&
+	    linkmode_test_bit(fd_bit, state->lp_advertising)) {
+		state->speed = speed;
+		state->duplex = DUPLEX_FULL;
+	} else {
+		/* negotiation failure */
+		state->link = false;
+	}
+
+	linkmode_resolve_pause(state->advertising, state->lp_advertising,
+			       &tx_pause, &rx_pause);
+
+	if (tx_pause)
+		state->pause |= MLO_PAUSE_TX;
+	if (rx_pause)
+		state->pause |= MLO_PAUSE_RX;
+}
+
+static void phylink_decode_sgmii_word(struct phylink_link_state *state,
+				      uint16_t config_reg)
+{
+	if (!(config_reg & BIT(15))) {
+		state->link = false;
+		return;
+	}
+
+	switch (config_reg & 0x0c00) {
+	case 0x0000:
+		state->speed = SPEED_10;
+		state->duplex = config_reg & 0x1000 ? DUPLEX_FULL : DUPLEX_HALF;
+		break;
+	case 0x0400:
+		state->speed = SPEED_100;
+		state->duplex = config_reg & 0x1000 ? DUPLEX_FULL : DUPLEX_HALF;
+		break;
+	case 0x0800:
+		state->speed = SPEED_1000;
+		state->duplex = config_reg & 0x1000 ? DUPLEX_FULL : DUPLEX_HALF;
+		break;
+	default:
+		state->link = false;
+		break;
+	}
+}
+
+/**
+ * phylink_mii_c22_pcs_get_state() - read the MAC PCS state
+ * @pcs: a pointer to a &struct mdio_device.
+ * @state: a pointer to a &struct phylink_link_state.
+ *
+ * Helper for MAC PCS supporting the 802.3 clause 22 register set for
+ * clause 37 negotiation and/or SGMII control.
+ *
+ * Read the MAC PCS state from the MII device configured in @config and
+ * parse the Clause 37 or Cisco SGMII link partner negotiation word into
+ * the phylink @state structure. This is suitable to be directly plugged
+ * into the mac_pcs_get_state() member of the struct phylink_mac_ops
+ * structure.
+ */
+void phylink_mii_c22_pcs_get_state(struct mdio_device *pcs,
+				   struct phylink_link_state *state)
+{
+	struct mii_bus *bus = pcs->bus;
+	int addr = pcs->addr;
+	int bmsr, lpa;
+
+	bmsr = mdiobus_read(bus, addr, MII_BMSR);
+	lpa = mdiobus_read(bus, addr, MII_LPA);
+	if (bmsr < 0 || lpa < 0) {
+		state->link = false;
+		return;
+	}
+
+	state->link = !!(bmsr & BMSR_LSTATUS);
+	state->an_complete = !!(bmsr & BMSR_ANEGCOMPLETE);
+	if (!state->link)
+		return;
+
+	switch (state->interface) {
+	case PHY_INTERFACE_MODE_1000BASEX:
+		phylink_decode_c37_word(state, lpa, SPEED_1000);
+		break;
+
+	case PHY_INTERFACE_MODE_2500BASEX:
+		phylink_decode_c37_word(state, lpa, SPEED_2500);
+		break;
+
+	case PHY_INTERFACE_MODE_SGMII:
+		phylink_decode_sgmii_word(state, lpa);
+		break;
+
+	default:
+		state->link = false;
+		break;
+	}
+}
+EXPORT_SYMBOL_GPL(phylink_mii_c22_pcs_get_state);
+
+/**
+ * phylink_mii_c22_pcs_set_advertisement() - configure the clause 37 PCS
+ *	advertisement
+ * @pcs: a pointer to a &struct mdio_device.
+ * @state: a pointer to the state being configured.
+ *
+ * Helper for MAC PCS supporting the 802.3 clause 22 register set for
+ * clause 37 negotiation and/or SGMII control.
+ *
+ * Configure the clause 37 PCS advertisement as specified by @state. This
+ * does not trigger a renegotiation; phylink will do that via the
+ * mac_an_restart() method of the struct phylink_mac_ops structure.
+ *
+ * Returns negative error code on failure to configure the advertisement,
+ * zero if no change has been made, or one if the advertisement has changed.
+ */
+int phylink_mii_c22_pcs_set_advertisement(struct mdio_device *pcs,
+					const struct phylink_link_state *state)
+{
+	struct mii_bus *bus = pcs->bus;
+	int addr = pcs->addr;
+	int val, ret;
+	u16 adv;
+
+	switch (state->interface) {
+	case PHY_INTERFACE_MODE_1000BASEX:
+	case PHY_INTERFACE_MODE_2500BASEX:
+		adv = ADVERTISE_1000XFULL;
+		if (linkmode_test_bit(ETHTOOL_LINK_MODE_Pause_BIT,
+				      state->advertising))
+			adv |= ADVERTISE_1000XPAUSE;
+		if (linkmode_test_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT,
+				      state->advertising))
+			adv |= ADVERTISE_1000XPSE_ASYM;
+
+		val = mdiobus_read(bus, addr, MII_ADVERTISE);
+		if (val < 0)
+			return val;
+
+		if (val == adv)
+			return 0;
+
+		ret = mdiobus_write(bus, addr, MII_ADVERTISE, adv);
+		if (ret < 0)
+			return ret;
+
+		return 1;
+
+	case PHY_INTERFACE_MODE_SGMII:
+		val = mdiobus_read(bus, addr, MII_ADVERTISE);
+		if (val < 0)
+			return val;
+
+		if (val == 0x0001)
+			return 0;
+
+		ret = mdiobus_write(bus, addr, MII_ADVERTISE, 0x0001);
+		if (ret < 0)
+			return ret;
+
+		return 1;
+
+	default:
+		/* Nothing to do for other modes */
+		return 0;
+	}
+}
+EXPORT_SYMBOL_GPL(phylink_mii_c22_pcs_set_advertisement);
+
+/**
+ * phylink_mii_c22_pcs_an_restart() - restart 802.3z autonegotiation
+ * @pcs: a pointer to a &struct mdio_device.
+ *
+ * Helper for MAC PCS supporting the 802.3 clause 22 register set for
+ * clause 37 negotiation.
+ *
+ * Restart the clause 37 negotiation with the link partner. This is
+ * suitable to be directly plugged into the mac_pcs_get_state() member
+ * of the struct phylink_mac_ops structure.
+ */
+void phylink_mii_c22_pcs_an_restart(struct mdio_device *pcs)
+{
+	struct mii_bus *bus = pcs->bus;
+	int val, addr = pcs->addr;
+
+	val = mdiobus_read(bus, addr, MII_BMCR);
+	if (val >= 0) {
+		val |= BMCR_ANRESTART;
+
+		mdiobus_write(bus, addr, MII_BMCR, val);
+	}
+}
+EXPORT_SYMBOL_GPL(phylink_mii_c22_pcs_an_restart);
+
 MODULE_LICENSE("GPL v2");
diff --git a/include/linux/phylink.h b/include/linux/phylink.h
index 2180eb1aa254..de591c2fb37e 100644
--- a/include/linux/phylink.h
+++ b/include/linux/phylink.h
@@ -317,4 +317,10 @@ int phylink_mii_ioctl(struct phylink *, struct ifreq *, int);
 void phylink_set_port_modes(unsigned long *bits);
 void phylink_helper_basex_speed(struct phylink_link_state *state);
 
+void phylink_mii_c22_pcs_get_state(struct mdio_device *pcs,
+				   struct phylink_link_state *state);
+int phylink_mii_c22_pcs_set_advertisement(struct mdio_device *pcs,
+					const struct phylink_link_state *state);
+void phylink_mii_c22_pcs_an_restart(struct mdio_device *pcs);
+
 #endif

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Implement helpers for PCS accessed via the MII bus using 802.3 clause
45 cycles for 10GBASE-R. Only link up/down is supported, 10G full
duplex is assumed.

Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/phylink.c | 30 ++++++++++++++++++++++++++++++
 include/linux/phylink.h   |  2 ++
 2 files changed, 32 insertions(+)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index 23a5e68d9222..bbe46d68be11 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -2268,4 +2268,34 @@ void phylink_mii_c22_pcs_an_restart(struct mdio_device *pcs)
 }
 EXPORT_SYMBOL_GPL(phylink_mii_c22_pcs_an_restart);
 
+#define C45_ADDR(d,a)	(MII_ADDR_C45 | (d) << 16 | (a))
+void phylink_mii_c45_pcs_get_state(struct mdio_device *pcs,
+				   struct phylink_link_state *state)
+{
+	struct mii_bus *bus = pcs->bus;
+	int addr = pcs->addr;
+	int stat;
+
+	stat = mdiobus_read(bus, addr, C45_ADDR(MDIO_MMD_PCS, MDIO_STAT1));
+	if (stat < 0) {
+		state->link = false;
+		return;
+	}
+
+	state->link = !!(stat & MDIO_STAT1_LSTATUS);
+	if (!state->link)
+		return;
+
+	switch (state->interface) {
+	case PHY_INTERFACE_MODE_10GBASER:
+		state->speed = SPEED_10000;
+		state->duplex = DUPLEX_FULL;
+		break;
+
+	default:
+		break;
+	}
+}
+EXPORT_SYMBOL_GPL(phylink_mii_c45_pcs_get_state);
+
 MODULE_LICENSE("GPL v2");
diff --git a/include/linux/phylink.h b/include/linux/phylink.h
index de591c2fb37e..8fa6df3b881b 100644
--- a/include/linux/phylink.h
+++ b/include/linux/phylink.h
@@ -323,4 +323,6 @@ int phylink_mii_c22_pcs_set_advertisement(struct mdio_device *pcs,
 					const struct phylink_link_state *state);
 void phylink_mii_c22_pcs_an_restart(struct mdio_device *pcs);
 
+void phylink_mii_c45_pcs_get_state(struct mdio_device *pcs,
+				   struct phylink_link_state *state);
 #endif

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Change phylink_mii_c22_pcs_set_advertisement() to take only the PHY
interface and advertisement mask, rather than the full phylink state.

Reviewed-by: Andrew Lunn <[email-masked]>
Reviewed-by: Florian Fainelli <[email-masked]>
Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/phylink.c | 12 +++++++-----
 include/linux/phylink.h   |  3 ++-
 2 files changed, 9 insertions(+), 6 deletions(-)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index bbe46d68be11..bf0c9d3ef344 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -2178,7 +2178,8 @@ EXPORT_SYMBOL_GPL(phylink_mii_c22_pcs_get_state);
  * phylink_mii_c22_pcs_set_advertisement() - configure the clause 37 PCS
  *	advertisement
  * @pcs: a pointer to a &struct mdio_device.
- * @state: a pointer to the state being configured.
+ * @interface: the PHY interface mode being configured
+ * @advertising: the ethtool advertisement mask
  *
  * Helper for MAC PCS supporting the 802.3 clause 22 register set for
  * clause 37 negotiation and/or SGMII control.
@@ -2191,22 +2192,23 @@ EXPORT_SYMBOL_GPL(phylink_mii_c22_pcs_get_state);
  * zero if no change has been made, or one if the advertisement has changed.
  */
 int phylink_mii_c22_pcs_set_advertisement(struct mdio_device *pcs,
-					const struct phylink_link_state *state)
+					  phy_interface_t interface,
+					  const unsigned long *advertising)
 {
 	struct mii_bus *bus = pcs->bus;
 	int addr = pcs->addr;
 	int val, ret;
 	u16 adv;
 
-	switch (state->interface) {
+	switch (interface) {
 	case PHY_INTERFACE_MODE_1000BASEX:
 	case PHY_INTERFACE_MODE_2500BASEX:
 		adv = ADVERTISE_1000XFULL;
 		if (linkmode_test_bit(ETHTOOL_LINK_MODE_Pause_BIT,
-				      state->advertising))
+				      advertising))
 			adv |= ADVERTISE_1000XPAUSE;
 		if (linkmode_test_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT,
-				      state->advertising))
+				      advertising))
 			adv |= ADVERTISE_1000XPSE_ASYM;
 
 		val = mdiobus_read(bus, addr, MII_ADVERTISE);
diff --git a/include/linux/phylink.h b/include/linux/phylink.h
index 8fa6df3b881b..6f6ecf3e0be1 100644
--- a/include/linux/phylink.h
+++ b/include/linux/phylink.h
@@ -320,7 +320,8 @@ void phylink_helper_basex_speed(struct phylink_link_state *state);
 void phylink_mii_c22_pcs_get_state(struct mdio_device *pcs,
 				   struct phylink_link_state *state);
 int phylink_mii_c22_pcs_set_advertisement(struct mdio_device *pcs,
-					const struct phylink_link_state *state);
+					  phy_interface_t interface,
+					  const unsigned long *advertising);
 void phylink_mii_c22_pcs_an_restart(struct mdio_device *pcs);
 
 void phylink_mii_c45_pcs_get_state(struct mdio_device *pcs,

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Rename the bland 'ops' member of struct phylink to be a more
descriptive 'mac_ops' - this is necessary as we're about to introduce
another set of operations.

Reviewed-by: Andrew Lunn <[email-masked]>
Reviewed-by: Florian Fainelli <[email-masked]>
Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/phylink.c | 30 +++++++++++++++---------------
 include/linux/phylink.h   |  2 +-
 2 files changed, 16 insertions(+), 16 deletions(-)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index bf0c9d3ef344..a8a6fd33b8bb 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -40,7 +40,7 @@ enum {
 struct phylink {
 	/* private: */
 	struct net_device *netdev;
-	const struct phylink_mac_ops *ops;
+	const struct phylink_mac_ops *mac_ops;
 	struct phylink_config *config;
 	struct device *dev;
 	unsigned int old_link_state:1;
@@ -154,7 +154,7 @@ static const char *phylink_an_mode_str(unsigned int mode)
 static int phylink_validate(struct phylink *pl, unsigned long *supported,
 			    struct phylink_link_state *state)
 {
-	pl->ops->validate(pl->config, supported, state);
+	pl->mac_ops->validate(pl->config, supported, state);
 
 	return phylink_is_empty_linkmode(supported) ? -EINVAL : 0;
 }
@@ -410,7 +410,7 @@ static void phylink_mac_config(struct phylink *pl,
 		    __ETHTOOL_LINK_MODE_MASK_NBITS, state->advertising,
 		    state->pause, state->link, state->an_enabled);
 
-	pl->ops->mac_config(pl->config, pl->cur_link_an_mode, state);
+	pl->mac_ops->mac_config(pl->config, pl->cur_link_an_mode, state);
 }
 
 static void phylink_mac_config_up(struct phylink *pl,
@@ -424,7 +424,7 @@ static void phylink_mac_an_restart(struct phylink *pl)
 {
 	if (pl->link_config.an_enabled &&
 	    phy_interface_mode_is_8023z(pl->link_config.interface))
-		pl->ops->mac_an_restart(pl->config);
+		pl->mac_ops->mac_an_restart(pl->config);
 }
 
 static void phylink_mac_pcs_get_state(struct phylink *pl,
@@ -440,7 +440,7 @@ static void phylink_mac_pcs_get_state(struct phylink *pl,
 	state->an_complete = 0;
 	state->link = 1;
 
-	pl->ops->mac_pcs_get_state(pl->config, state);
+	pl->mac_ops->mac_pcs_get_state(pl->config, state);
 }
 
 /* The fixed state is... fixed except for the link state,
@@ -507,11 +507,11 @@ static void phylink_mac_link_up(struct phylink *pl,
 	struct net_device *ndev = pl->netdev;
 
 	pl->cur_interface = link_state.interface;
-	pl->ops->mac_link_up(pl->config, pl->phydev,
-			     pl->cur_link_an_mode, pl->cur_interface,
-			     link_state.speed, link_state.duplex,
-			     !!(link_state.pause & MLO_PAUSE_TX),
-			     !!(link_state.pause & MLO_PAUSE_RX));
+	pl->mac_ops->mac_link_up(pl->config, pl->phydev,
+				 pl->cur_link_an_mode, pl->cur_interface,
+				 link_state.speed, link_state.duplex,
+				 !!(link_state.pause & MLO_PAUSE_TX),
+				 !!(link_state.pause & MLO_PAUSE_RX));
 
 	if (ndev)
 		netif_carrier_on(ndev);
@@ -529,8 +529,8 @@ static void phylink_mac_link_down(struct phylink *pl)
 
 	if (ndev)
 		netif_carrier_off(ndev);
-	pl->ops->mac_link_down(pl->config, pl->cur_link_an_mode,
-			       pl->cur_interface);
+	pl->mac_ops->mac_link_down(pl->config, pl->cur_link_an_mode,
+				   pl->cur_interface);
 	phylink_info(pl, "Link is Down\n");
 }
 
@@ -661,7 +661,7 @@ static int phylink_register_sfp(struct phylink *pl,
  * @fwnode: a pointer to a &struct fwnode_handle describing the network
  *	interface
  * @iface: the desired link mode defined by &typedef phy_interface_t
- * @ops: a pointer to a &struct phylink_mac_ops for the MAC.
+ * @mac_ops: a pointer to a &struct phylink_mac_ops for the MAC.
  *
  * Create a new phylink instance, and parse the link parameters found in @np.
  * This will parse in-band modes, fixed-link or SFP configuration.
@@ -674,7 +674,7 @@ static int phylink_register_sfp(struct phylink *pl,
 struct phylink *phylink_create(struct phylink_config *config,
 			       struct fwnode_handle *fwnode,
 			       phy_interface_t iface,
-			       const struct phylink_mac_ops *ops)
+			       const struct phylink_mac_ops *mac_ops)
 {
 	struct phylink *pl;
 	int ret;
@@ -707,7 +707,7 @@ struct phylink *phylink_create(struct phylink_config *config,
 	pl->link_config.speed = SPEED_UNKNOWN;
 	pl->link_config.duplex = DUPLEX_UNKNOWN;
 	pl->link_config.an_enabled = true;
-	pl->ops = ops;
+	pl->mac_ops = mac_ops;
 	__set_bit(PHYLINK_DISABLE_STOPPED, &pl->phylink_disable_state);
 	timer_setup(&pl->link_poll, phylink_fixed_poll, 0);
 
diff --git a/include/linux/phylink.h b/include/linux/phylink.h
index 6f6ecf3e0be1..90c907eaae15 100644
--- a/include/linux/phylink.h
+++ b/include/linux/phylink.h
@@ -272,7 +272,7 @@ void mac_link_up(struct phylink_config *config, struct phy_device *phy,
 
 struct phylink *phylink_create(struct phylink_config *, struct fwnode_handle *,
 			       phy_interface_t iface,
-			       const struct phylink_mac_ops *ops);
+			       const struct phylink_mac_ops *mac_ops);
 void phylink_destroy(struct phylink *);
 
 int phylink_connect_phy(struct phylink *, struct phy_device *);

---

From: Russell King <[email-masked]>
Date: Thu, 02 Apr 2020 11:48:02 +0100

Add a separate set of PCS operations, which MAC drivers can use to
couple phylink with their associated MAC PCS layer.  The PCS
operations include:

- pcs_get_state() - reads the link up/down, resolved speed, duplex
   and pause from the PCS.
- pcs_config() - configures the PCS for the specified mode, PHY
   interface type, and setting the advertisement.
- pcs_an_restart() - restarts 802.3 in-band negotiation with the
   link partner
- pcs_link_up() - informs the PCS that link has come up, and the
   parameters of the link. Link parameters are used to program the
   PCS for fixed speed and non-inband modes.

Reviewed-by: Andrew Lunn <[email-masked]>
Reviewed-by: Florian Fainelli <[email-masked]>
Signed-off-by: Russell King <[email-masked]>
---
 drivers/net/phy/phylink.c | 77 +++++++++++++++++++++++++++++------------
 include/linux/phylink.h   | 88 +++++++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 143 insertions(+), 22 deletions(-)

diff --git a/drivers/net/phy/phylink.c b/drivers/net/phy/phylink.c
index a8a6fd33b8bb..d830108f7a8e 100644
--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -41,6 +41,7 @@ struct phylink {
 	/* private: */
 	struct net_device *netdev;
 	const struct phylink_mac_ops *mac_ops;
+	const struct phylink_pcs_ops *pcs_ops;
 	struct phylink_config *config;
 	struct device *dev;
 	unsigned int old_link_state:1;
@@ -420,11 +421,32 @@ static void phylink_mac_config_up(struct phylink *pl,
 		phylink_mac_config(pl, state);
 }
 
-static void phylink_mac_an_restart(struct phylink *pl)
+static void phylink_mac_pcs_an_restart(struct phylink *pl)
 {
 	if (pl->link_config.an_enabled &&
-	    phy_interface_mode_is_8023z(pl->link_config.interface))
-		pl->mac_ops->mac_an_restart(pl->config);
+	    phy_interface_mode_is_8023z(pl->link_config.interface)) {
+		if (pl->pcs_ops)
+			pl->pcs_ops->pcs_an_restart(pl->config);
+		else
+			pl->mac_ops->mac_an_restart(pl->config);
+	}
+}
+
+static void phylink_pcs_config(struct phylink *pl, bool force_restart,
+			       const struct phylink_link_state *state)
+{
+	bool restart = force_restart;
+
+	if (pl->pcs_ops && pl->pcs_ops->pcs_config(pl->config,
+						   pl->cur_link_an_mode,
+						   state->interface,
+						   state->advertising))
+		restart = true;
+
+	phylink_mac_config(pl, state);
+
+	if (restart)
+		phylink_mac_pcs_an_restart(pl);
 }
 
 static void phylink_mac_pcs_get_state(struct phylink *pl,
@@ -440,7 +462,10 @@ static void phylink_mac_pcs_get_state(struct phylink *pl,
 	state->an_complete = 0;
 	state->link = 1;
 
-	pl->mac_ops->mac_pcs_get_state(pl->config, state);
+	if (pl->pcs_ops)
+		pl->pcs_ops->pcs_get_state(pl->config, state);
+	else
+		pl->mac_ops->mac_pcs_get_state(pl->config, state);
 }
 
 /* The fixed state is... fixed except for the link state,
@@ -458,7 +483,7 @@ static void phylink_get_fixed_state(struct phylink *pl,
 	phylink_resolve_flow(state);
 }
 
-static void phylink_mac_initial_config(struct phylink *pl)
+static void phylink_mac_initial_config(struct phylink *pl, bool force_restart)
 {
 	struct phylink_link_state link_state;
 
@@ -484,7 +509,7 @@ static void phylink_mac_initial_config(struct phylink *pl)
 	link_state.link = false;
 
 	phylink_apply_manual_flow(pl, &link_state);
-	phylink_mac_config(pl, &link_state);
+	phylink_pcs_config(pl, force_restart, &link_state);
 }
 
 static const char *phylink_pause_to_str(int pause)
@@ -501,12 +526,18 @@ static const char *phylink_pause_to_str(int pause)
 	}
 }
 
-static void phylink_mac_link_up(struct phylink *pl,
-				struct phylink_link_state link_state)
+static void phylink_link_up(struct phylink *pl,
+			    struct phylink_link_state link_state)
 {
 	struct net_device *ndev = pl->netdev;
 
 	pl->cur_interface = link_state.interface;
+
+	if (pl->pcs_ops && pl->pcs_ops->pcs_link_up)
+		pl->pcs_ops->pcs_link_up(pl->config, pl->cur_link_an_mode,
+					 pl->cur_interface,
+					 link_state.speed, link_state.duplex);
+
 	pl->mac_ops->mac_link_up(pl->config, pl->phydev,
 				 pl->cur_link_an_mode, pl->cur_interface,
 				 link_state.speed, link_state.duplex,
@@ -523,7 +554,7 @@ static void phylink_mac_link_up(struct phylink *pl,
 		     phylink_pause_to_str(link_state.pause));
 }
 
-static void phylink_mac_link_down(struct phylink *pl)
+static void phylink_link_down(struct phylink *pl)
 {
 	struct net_device *ndev = pl->netdev;
 
@@ -592,9 +623,9 @@ static void phylink_resolve(struct work_struct *w)
 	if (link_changed) {
 		pl->old_link_state = link_state.link;
 		if (!link_state.link)
-			phylink_mac_link_down(pl);
+			phylink_link_down(pl);
 		else
-			phylink_mac_link_up(pl, link_state);
+			phylink_link_up(pl, link_state);
 	}
 	if (!link_state.link && pl->mac_link_dropped) {
 		pl->mac_link_dropped = false;
@@ -741,6 +772,12 @@ struct phylink *phylink_create(struct phylink_config *config,
 }
 EXPORT_SYMBOL_GPL(phylink_create);
 
+void phylink_add_pcs(struct phylink *pl, const struct phylink_pcs_ops *ops)
+{
+	pl->pcs_ops = ops;
+}
+EXPORT_SYMBOL_GPL(phylink_add_pcs);
+
 /**
  * phylink_destroy() - cleanup and destroy the phylink instance
  * @pl: a pointer to a &struct phylink returned from phylink_create()
@@ -1077,14 +1114,12 @@ void phylink_start(struct phylink *pl)
 	/* Apply the link configuration to the MAC when starting. This allows
 	 * a fixed-link to start with the correct parameters, and also
 	 * ensures that we set the appropriate advertisement for Serdes links.
-	 */
-	phylink_mac_initial_config(pl);
-
-	/* Restart autonegotiation if using 802.3z to ensure that the link
+	 *
+	 * Restart autonegotiation if using 802.3z to ensure that the link
 	 * parameters are properly negotiated.  This is necessary for DSA
 	 * switches using 802.3z negotiation to ensure they see our modes.
 	 */
-	phylink_mac_an_restart(pl);
+	phylink_mac_initial_config(pl, true);
 
 	clear_bit(PHYLINK_DISABLE_STOPPED, &pl->phylink_disable_state);
 	phylink_run_resolve(pl);
@@ -1381,8 +1416,7 @@ int phylink_ethtool_ksettings_set(struct phylink *pl,
 			 * advertisement; the only thing we have is the pause
 			 * modes which can only come from a PHY.
 			 */
-			phylink_mac_config(pl, &pl->link_config);
-			phylink_mac_an_restart(pl);
+			phylink_pcs_config(pl, true, &pl->link_config);
 		}
 		mutex_unlock(&pl->state_mutex);
 	}
@@ -1410,7 +1444,7 @@ int phylink_ethtool_nway_reset(struct phylink *pl)
 
 	if (pl->phydev)
 		ret = phy_restart_aneg(pl->phydev);
-	phylink_mac_an_restart(pl);
+	phylink_mac_pcs_an_restart(pl);
 
 	return ret;
 }
@@ -1489,8 +1523,7 @@ int phylink_ethtool_set_pauseparam(struct phylink *pl,
 				   pause->tx_pause);
 	} else if (!test_bit(PHYLINK_DISABLE_STOPPED,
 			     &pl->phylink_disable_state)) {
-		phylink_mac_config(pl, &pl->link_config);
-		phylink_mac_an_restart(pl);
+		phylink_pcs_config(pl, true, &pl->link_config);
 	}
 	mutex_unlock(&pl->state_mutex);
 
@@ -1896,7 +1929,7 @@ static int phylink_sfp_config(struct phylink *pl, u8 mode,
 
 	if (changed && !test_bit(PHYLINK_DISABLE_STOPPED,
 				 &pl->phylink_disable_state))
-		phylink_mac_initial_config(pl);
+		phylink_mac_initial_config(pl, false);
 
 	return ret;
 }
diff --git a/include/linux/phylink.h b/include/linux/phylink.h
index 90c907eaae15..3f8d37ec5503 100644
--- a/include/linux/phylink.h
+++ b/include/linux/phylink.h
@@ -270,9 +270,97 @@ void mac_link_up(struct phylink_config *config, struct phy_device *phy,
 		 int speed, int duplex, bool tx_pause, bool rx_pause);
 #endif
 
+/**
+ * struct phylink_pcs_ops - MAC PCS operations structure.
+ * @pcs_get_state: read the current MAC PCS link state from the hardware.
+ * @pcs_config: configure the MAC PCS for the selected mode and state.
+ * @pcs_an_restart: restart 802.3z BaseX autonegotiation.
+ * @pcs_link_up: program the PCS for the resolved link configuration
+ *               (where necessary).
+ */
+struct phylink_pcs_ops {
+	void (*pcs_get_state)(struct phylink_config *config,
+			      struct phylink_link_state *state);
+	int (*pcs_config)(struct phylink_config *config, unsigned int mode,
+			  phy_interface_t interface,
+			  const unsigned long *advertising);
+	void (*pcs_an_restart)(struct phylink_config *config);
+	void (*pcs_link_up)(struct phylink_config *config, unsigned int mode,
+			    phy_interface_t interface, int speed, int duplex);
+};
+
+#if 0 /* For kernel-doc purposes only. */
+/**
+ * pcs_get_state() - Read the current inband link state from the hardware
+ * @config: a pointer to a &struct phylink_config.
+ * @state: a pointer to a &struct phylink_link_state.
+ *
+ * Read the current inband link state from the MAC PCS, reporting the
+ * current speed in @state->speed, duplex mode in @state->duplex, pause
+ * mode in @state->pause using the %MLO_PAUSE_RX and %MLO_PAUSE_TX bits,
+ * negotiation completion state in @state->an_complete, and link up state
+ * in @state->link. If possible, @state->lp_advertising should also be
+ * populated.
+ *
+ * When present, this overrides mac_pcs_get_state() in &struct
+ * phylink_mac_ops.
+ */
+void pcs_get_state(struct phylink_config *config,
+		   struct phylink_link_state *state);
+
+/**
+ * pcs_config() - Configure the PCS mode and advertisement
+ * @config: a pointer to a &struct phylink_config.
+ * @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND.
+ * @interface: interface mode to be used
+ * @advertising: adertisement ethtool link mode mask
+ *
+ * Configure the PCS for the operating mode, the interface mode, and set
+ * the advertisement mask.
+ *
+ * When operating in %MLO_AN_INBAND, inband should always be enabled,
+ * otherwise inband should be disabled.
+ *
+ * For SGMII, there is no advertisement from the MAC side, the PCS should
+ * be programmed to acknowledge the inband word from the PHY.
+ *
+ * For 1000BASE-X, the advertisement should be programmed into the PCS.
+ *
+ * For most 10GBASE-R, there is no advertisement.
+ */
+int (*pcs_config)(struct phylink_config *config, unsigned int mode,
+		  phy_interface_t interface, const unsigned long *advertising);
+
+/**
+ * pcs_an_restart() - restart 802.3z BaseX autonegotiation
+ * @config: a pointer to a &struct phylink_config.
+ *
+ * When PCS ops are present, this overrides mac_an_restart() in &struct
+ * phylink_mac_ops.
+ */
+void (*pcs_an_restart)(struct phylink_config *config);
+
+/**
+ * pcs_link_up() - program the PCS for the resolved link configuration
+ * @config: a pointer to a &struct phylink_config.
+ * @mode: link autonegotiation mode
+ * @interface: link &typedef phy_interface_t mode
+ * @speed: link speed
+ * @duplex: link duplex
+ *
+ * This call will be made just before mac_link_up() to inform the PCS of
+ * the resolved link parameters. For example, a PCS operating in SGMII
+ * mode without in-band AN needs to be manually configured for the link
+ * and duplex setting. Otherwise, this should be a no-op.
+ */
+void (*pcs_link_up)(struct phylink_config *config, unsigned int mode,
+		    phy_interface_t interface, int speed, int duplex);
+#endif
+
 struct phylink *phylink_create(struct phylink_config *, struct fwnode_handle *,
 			       phy_interface_t iface,
 			       const struct phylink_mac_ops *mac_ops);
+void phylink_add_pcs(struct phylink *, const struct phylink_pcs_ops *ops);
 void phylink_destroy(struct phylink *);